Brake Shudder or Vibration – 2003 Dodge Durango

“This site contains affiliate links for which OEMDTC may be compensated”

NUMBER: 05-007-03
GROUP: Brakes
DATE: Nov. 14, 2003

 

SUBJECT:

Brake Shudder or Vibration

 

OVERVIEW:

This bulletin involves installing brake pads, resurfacing the rotors and check rotor runout.

 

MODELS:

2003 (DN) Durango

 

SYMPTOM/CONDITION:

The vehicle may exhibit pulsation or vibration in the brake pedal and/or steering wheel when the brakes are applied. The condition is most noticeable at speed over 50 MPH but can occur at lower speeds.

 

DIAGNOSIS:

If the customers indicate that the condition is present, perform the Repair Procedure.

 

PARTS REQUIRED:

Qty. Part No. Description
1 05093796AB Brake Pads

 

SPECIAL TOOLS/EQUIPMENT REQUIRED:

ProCut Hunter
One of the Following

DaimlerChrysler Approved On Car Disc Rotor Lathes:

PC-610, PC-CHRYSLER, PC-TRUCK, PC-CROSTRUCK, PC-PFMTRUCK, PC-PFMCHRYSLER, PC-PFM900, PC-PFMCHRYSLER-95, PC-PFMTRUCK-95, PC-PFM900-95, PC-PFM90.2, PC-PFM90.4, PC-PFM90 – H-OCL360, H-OCL360-LT-PRO, H-OCL360-LT-PSE,
H-OCL360A, H-OCL360A-LT-PRO, H-OCL360A-LT-PSE, H-OCL360S,
H-OCL360S-LT-PRO, H-OCL360S-LT-PSE

 

REPAIR PROCEDURE:

  1. Inspect the front brakes for any signs of abnormal wear or damage. Repair as necessary.
  2. Resurface the front brake rotors with a DaimlerChrylsler approved on-car brake lathe. If an on-car lathe is not available at the dealership, the rotor resurfacing must be sublet to a facility with an approved on car lathe.
  3. Remove the calipers.
  4. Replace the front linings with 05093796AB.
  5. Mark one wheel stud on each side with a dab of paint or suitable marker.

NOTE: Wheel stud torque is critical to the success of the repair. the following procedure is intended to identify excessive rotor distortion which could be caused by improper wheel stud torque.

  1. Install the wheel and pre-tighten the lug nuts in a cross pattern to: 70 Nm (50 ft. lbs.) then final the lug nuts in a cross pattern to: 135 Nm (100 ft. lbs.) and mark the wheel at the same location as the marked wheel stud.
  2. Set up a dial indicator to measure mounted rotor runout . Place the dial indicator plunger against the inner machined rotor face, visible between the brake caliper and the front splash shield. Rotate the wheel and tire assembly two turns and take runout measurement. If the measurement is less than .050 mm (.002 in.) no further action is required. If the measurement is greater than .050 mm (.002 in.) remove the lug nuts and relocate the wheel one stud clockwise, tighten the lug nuts as described in step 8 and check the runout again. Do not remove any brake parts. Repeat step 9 for each wheel location until you achieve the lowest mounted runout. Minimum mounted rotor runout will be achieved by moving the wheel, not the rotor.

 

POLICY:

Reimbursable within the provisions of the warranty.

 

TIME ALLOWANCE:

Labor Operation No: Description Amount
05-21-11-90 Replace Brake Pads, Resurface Rotors and Check Rotor Run Out 1.8 Hrs.

 

FAILURE CODE:

2X Vibration or Chatter

 

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [15.51 KB]

 

 

Leave a Comment

Share to...