Flash: Transmission Diagnostic and Shift Enhancements – 2015 Jeep Cherokee & Chrysler 200

“This site contains affiliate links for which OEMDTC may be compensated”

NUMBER: 21-001-18
GROUP: 21 – Transmission and Transfer Case
DATE: January 4, 2018

 

THIS BULLETIN SUPERSEDES SERVICE BULLETIN 21-019-17 REV. A, DATED SEPTEMBER 09, 2017. WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE MARKED WITH **ASTERISKS** AND INCLUDE ASSIGNING THE BULLETIN A NEW RRT NUMBER AND LOPS.

THIS SERVICE BULLETIN IS ALSO BEING RELEASED AS RAPID RESPONSE TRANSMITTAL (RRT) **18-001**. ALL APPLICABLE SOLD AND UN-SOLD RRT VIN’s HAVE BEEN LOADED.

TO VERIFY THAT THIS RRT SERVICE ACTION IS APPLICABLE TO THE VEHICLE, USE VIP OR PERFORM A VIN SEARCH IN TECHCONNECT. ALL REPAIRS ARE REIMBURSABLE WITHIN THE PROVISIONS OF WARRANTY.

FOR HELP WITH USING wiTECH FOR ECU FLASH REPROGRAMMING, CLICK ON THE APPLICATION’S “HELP” TAB.

THE wiTECH SOFTWARE IS REQUIRED TO BE AT THE LATEST RELEASE BEFORE PERFORMING THIS PROCEDURE.

 

SUBJECT:

Flash: Transmission Diagnostic and Shift Enhancements

 

OVERVIEW:

This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software.

 

MODELS:

2015 (KL) Jeep Cherokee
2015 (UF) Chrysler 200

 

NOTE: This bulletin applies to vehicles within the following markets/countries: NAFTA, APAC and EMEA.

NOTE: This bulletin applies to the following vehicles:

 

SYMPTOM/CONDITION:

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination and/or one of the following conditions. Upon further investigation, a technician may find one or more of the following DTCs stored in the TCM memory.

 

2015 KL Vehicles

  • P1634-00 – TCM Internal Watchdog Performance (Sales Codes ED6 or ED8 Only).
  • U1412 – Implausible Vehicle Speed Signal Received.
  • U0001 – Can C Bus.
  • P0887-00 – TCM Power Control Circuit High.
  • P061B-00 – Internal Control Module Torque Calculation Performance.
  • U0401-00 – Implausible Data Received From ECM/PCM.
  • P1DAD-00 – Input Shaft-Output Shaft Direction Correlation.
  • P0711-00 – Transmission Fluid Temperature Sensor A Circuit Range-Performance (ED6 or ED8 Only).

In addition, some customers may experience one or more of the following conditions:

  • When driving on grades, the 3-2 downshift is hard to achieve or not available.

Other enhancements included in this update:

  • Garage shift improvements.
  • Shift improvements for 2-1 shift quality when using Electronic Range Sensor (ERS) function for 2-1 downshift and 3-1 shift quality (bump) when coasting to a stop (ED6 or ED8).

 

2015 UF Vehicles

  • P072F-00 – Stuck In Gear 4.
  • P061B-00 – Internal Control Module Torque Calculation Performance.
  • P0711-00 – Transmission Fluid Temperature Sensor A Circuit Range-Performance (ED6, ED8, EDD or EDE Only).
  • P0885-00 – TCM Power Control Circuit (ED6, ED8, EDD or EDE Only).
  • P0975-00 – Shift Solenoid B Control Circuit Performance (ED6, ED8, EDD or EDE Only).
  • P0887-00 – TCM Power Control Circuit High (ED6, ED8, EDD or EDE Only).
  • P0978-00 – Shift Solenoid 3 Control Circuit Performance (ED6, ED8, EDD or EDE Only).
  • P0981-00 – Shift Solenoid 4 Control Circuit Performance (ED6, ED8, EDD or EDE Only).
  • P0984-00 – Shift Solenoid 5 Control Circuit Performance (ED6, ED8, EDD or EDE Only).
  • P1634-00 – TCM Internal Watchdog Performance (ERB Only).
  • U0401-00 – Implausible Data Received From ECM/PCM.
  • P1DAD-00 – Input Shaft-Output Shaft Direction Correlation.

In addition, some customers may experience one or more of the following conditions:

  • When driving on grades, the 3-2 downshift is hard to achieve or not available (ED6, ED8, EDD or EDE Only).
  • 2-1 downshift and 3-1 shift quality (bump) when coasting to a stop (ED6, ED8, EDD or EDE Only).

Other enhancements included in this update:

  • Garage shift improvements (ED6,ED8,EDD or EDE Only).
  • Up shift improvements, 2-3, 3-4 or 4-5 (ERB Only).

 

DIAGNOSIS:

Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in TechCONNECT, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the ones listed above are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin.

If a customer’s VIN is listed in VIP or your RRT VIN list, perform the repair. If any vehicle not on the VIN list exhibits the symptom/condition or DTC, perform the repair.

 

REPAIR PROCEDURE:

NOTE: This TCM calibration update being released also enables the new wiTECH based “Transmission Quick Learn” procedure to be performed any time the transmission adaptation memory cells are cleared or when addressing customer concerns of poor shift quality. It is also being released to improve transmission downshift response time during normal driving.

NOTE: Install a battery charger Flash: Transmission Diagnostic and Shift Enhancements - 2015 Jeep Cherokee & Chrysler 200 | small light to ensure battery voltage does not drop below 13.2 volts. Do not allow the charging voltage to climb above 13.5 volts during the flash process.

NOTE: If this flash process is interrupted/aborted, the flash should be restarted.

  1. Using wiTECH, check the TCM calibration and see if it is up to date. Does the TCM software needs to be updated?
    • Yes >>> Proceed to Step 2.
    • No >>> The RRT has been completed. Use inspection LOP (**18-19-05-HK**) to close the active RRT.
  2. Reprogram the TCM with the latest software. Detailed instructions for flashing control modules using the wiTECH Diagnostic Application are available by selecting the application’s “HELP” tab.
  3. Using wiTECH, Perform the TCM “VIN Verification” routine Located in the TCM “Misc Functions” menu and follow the on-screen prompts.
  4. Using wiTECH, perform a “PROXI Configuration Alignment” routine located in the “Vehicle Preparations” tab on the main vehicle view screen.
  5. Turn the ignition off and disconnect wiTECH for 1 minute.
  6. Turn the ignition back on and reconnect wiTECH.
  7. From the vehicle view screen, select “PROXI Configuration Alignment” routine again in the “Vehicle Preparations” tab and verify all modules are properly aligned.
  8. Clear all DTCs that may have been set in any module due to reprogramming. The wiTECH application will automatically present all DTCs after the flash and allow them to be cleared. Proceed to Step 9.

NOTE: The Powertrain Control Module (PCM) must be updated to the latest available software to allow the quick learn procedure to function. Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding updating the PCM software.

NOTE: This flash will clear the transmission adaptive values which requires the “Transmission Quick Learn” procedure to be performed.

  1. Start the engine and monitor the transmission temperature on the Electronic Vehicle Information Center (EVIC).
  1. With the vehicle located in a suitable area, allow the transmission to warm up to minimum of 60° C (140° F) by performing the following steps:
    1. Apply the service brake.
    2. Shift transmission from Park to Reverse.
    3. Shift transmission from Reverse to Drive.
    4. Accelerate the vehicle to minimum of 72 kph (45 mph) to allow the transmission to cycle through each gear.
    5. Continue to drive the vehicle until the transmission temperature reaches 60° C (140° F).

NOTE: If the vehicle is equipped with the start/stop feature (sales code XBU) it must be disabled prior to performing this procedure. To disable, press the on/off switch located on the center switch bank near the HVAC controls.

  1. Connect wiTECH diagnostic scan too to the vehicle.
  2. Check for active TCM DTCs. Do not perform the Quick Learn procedure if TCM DTCs are present. Repair transmission as required.
  3. Select the TCM module in wiTECH.
  4. Select the “Misc Functions” tab.

NOTE: If the “Quick Learn” option does not appear on wiTECH and both the TCM and PCM were just updated, restart the wiTECH application which should now be populated with the “Quick Learn” option.

  1. Select the “Quick Learn” procedure, and follow the on-screen instructions to reset and learn the clutch adaptive values.
  2. Shift the transmission into Park and shut off the engine. The procedure is now complete.

 

POLICY:

Reimbursable within the provisions of the warranty.

 

TIME ALLOWANCE:

Labor Operation No: Description Skill Category Amount
**18-19-05-HM Module, Transmission Control (TCM) Reprogram and Perform Transmission Quick Learn UF Vehicle (0 – Introduction) 2 – Automatic Transmission 0.7 Hrs
18-19-05-HK Module, Transmission Control (TCM) Inspect Only. KL Vehicle (0 – Introduction) 2 – Automatic Transmission 0.2 Hrs
18-19-05-HL Module, Transmission Control (TCM) Reprogram and Perform Transmission Quick Learn KL Vehicle) (0 – Introduction) 2 – Automatic Transmission 0.7 Hrs**

 

NOTE: The expected completion time for the flash download portion of this procedure is approximately 4 minutes. Actual flash download times may be affected by vehicle connection and network capabilities.

 

FAILURE CODE:

The dealer must choose which failure code to use depending on if this is a Rapid Response Transmittal (RRT) or Service Bulletin.

  • If the customer’s concern matches the SYMPTOM/CONDITION identified in the Service Bulletin, failure code CC is to be used. When utilizing this failure code, the 3C’s must be supplied.
  • The failure code “RF” (Required Flash) can no longer be used on Service Bulletin flashes. The “RF” failure code can only be used on RRT.
  • The “RF” failure code is required for essential module flash/reprogramming and can only be used after confirmation that the VIN is included on the RRT.
CC Customer Concern
RF Required Flash

 


 

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [38.64 KB]

 


 

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [38.78 KB]

 


NUMBER: 21-015-16
GROUP: Transmission and Transfer Case
DATE: April 05, 2016

https://www.nhtsa.gov/recalls?nhtsaId=10074982

https://static.nhtsa.gov/odi/tsbs/2016/SB-10074982-5290.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [42.08 KB]

 


 

NUMBER: 21-021-15 REV. E
GROUP: Transmission and Transfer Case
DATE: October 01, 2015

https://www.nhtsa.gov/recalls?nhtsaId=10058038

https://static.nhtsa.gov/odi/tsbs/2015/SB-10058038-4700.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [131.54 KB]

 


NUMBER: 21-021-15 REV. D
GROUP: Transmission and Transfer Case
DATE: August 14, 2015

https://www.nhtsa.gov/recalls?nhtsaId=10058038

https://static.nhtsa.gov/odi/tsbs/2015/SB-10058038-2300.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [101.75 KB]

 


NUMBER: 21-021-15 REV. C
GROUP: Transmission and Transfer Case
DATE: August 05, 2015

https://www.nhtsa.gov/recalls?nhtsaId=10058038

https://static.nhtsa.gov/odi/tsbs/2015/SB-10058038-5549.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [100.55 KB]

 


NUMBER: 21-021-15 REV. B
GROUP: Transmission and
Transfer Case
DATE: June 20, 2015

https://www.nhtsa.gov/recalls?nhtsaId=10058038

https://static.nhtsa.gov/odi/tsbs/2015/SB-10058038-3733.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [24.18 KB]

 


NUMBER: 21-021-15
GROUP: Transmission and Transfer Case
DATE: March 28, 2015

https://www.nhtsa.gov/recalls?nhtsaId=10144860

https://static.nhtsa.gov/odi/tsbs/2015/MC-10144860-9999.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [39.72 KB]

 


 

Reprogramming

Chrysler J2534 Application Overview

 

DRB III Emulator

Flash Availability - J2534/Pass Thru Device

Vehicle to Diagnostic Tool Reference Chart

 

Chrysler Recommended J2534 Devices

For Chrysler recommended J2534 device, see below table.

J2534 Device Firmware Version
CTC Vehicle Box * 1.9
UCAN 2 1.0
Blue Streak -2534 Global Programmer 2.10
Actia I+ME Passthru 2.07

* Chrysler recommends the CTC Vehicle Box Device for Chrysler SCI ECU reprogramming. SCI reprogramming is used on most PCMs and TCMs prior to the introduction of CAN bus vehicles which began in 2004 (Durango).

 

Compatible J2534 Devices

Flash: Transmission Diagnostic and Shift Enhancements - 2015 Jeep Cherokee & Chrysler 200 | small light CarDAQ-Plus 3 All Makes J2534 Reprogramming Tool
Flash: Transmission Diagnostic and Shift Enhancements - 2015 Jeep Cherokee & Chrysler 200 | small light CarDAQ-Plus 2 Diagnostic Code Reader and J2534 Programming Tool
Flash: Transmission Diagnostic and Shift Enhancements - 2015 Jeep Cherokee & Chrysler 200 | small light CarDAQ-Plus
Flash: Transmission Diagnostic and Shift Enhancements - 2015 Jeep Cherokee & Chrysler 200 | small light CarDAQ-M
Flash: Transmission Diagnostic and Shift Enhancements - 2015 Jeep Cherokee & Chrysler 200 | small light VSI J2534 ECU Reprogrammer
Flash: Transmission Diagnostic and Shift Enhancements - 2015 Jeep Cherokee & Chrysler 200 | small light

Bosch Automotive Tools MTECH2 Mastertech II J2534 VCI with Wired/Wireless Capability for OEM Reprogramming and Diagnostics on GM, Ford, FCA, Nissan/Infiniti, Honda/Acura, and Toyota/Lexus Vehicles

RAP2 OEM J2534 Remote Reprogramming Tool

Flash: Transmission Diagnostic and Shift Enhancements - 2015 Jeep Cherokee & Chrysler 200 | small light

BOSCH Automotive Tools MTECH2 Mastertech II J2534 VCI

Flash: Transmission Diagnostic and Shift Enhancements - 2015 Jeep Cherokee & Chrysler 200 | small light

Autel MaxiFlash VCI Vehicle Communication Interface J2534 PassThru ECU Programming Device Bluetooth Connection Internet Update Support CAN FD, 4 CAN Channels, DoIP, D-PDU Works with PC or Autel MS909

Flash: Transmission Diagnostic and Shift Enhancements - 2015 Jeep Cherokee & Chrysler 200 | small light

GODIAG J2534

 


Click on the link below to:

Download J2534 Application

(Install the wiTECH 2.0 J2534 Application on your computer)

Download the Setup Utility

(Configure your microPod/MDP device)

Launch wiTECH 2.0

(Once subscription and users are assigned to a tool please follow this link to access wiTECH)

https://www.mopartsp.com/support

 


Chrysler J2534 Manual

wiTECH Software

www.techauthority.com

 


 

Bestseller No. 1
CarDAQ-Plus 3 All Makes J2534 Reprogramming Tool
  • ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
  • J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
  • TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
  • J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
  • FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
Bestseller No. 2
VNCI J2534 for Nano Diagnostic Tools,Support J2534 for Automatic Switch Mode Fast Communication
  • Application:Support most all of J2534 compatible software, most all of for software, ECU reprogramming in J2534 mode with programming voltage, supply software for diagnosing J1979 compatible vehicles.
  • Material:VNCI (Vehicle network communication interface) is a device that works between diagnostic software and vehicle. It is compatible with J2534 Passthru and for .
  • Advantage:Support J2534 and for mode in one device, and has automatic switch mode, more speedup, faster communication and reprogramming.VNCI J2534 for Nano protocol configuration include, for ISO15765, for ISO9141, for ISO14230, for J1850 PWM( supports IFR and 2X speed modes), for J1850 VPW (supports 4x speed mode).
  • Easy to install:More stability, never let you down while reprogramming, portable and convenient, small package and easy to carry.
  • Best Experience :We strive to provide you with the best quality products and the best customer experience.We try our best to meet your requirements.Please check the product information carefuly berore buying to aviod making mistakes.
Bestseller No. 3
Autel MaxiFlash Elite VCI J2534 Pass-Thru ECU Programming Tool, Multi-Protocol PassThru Interface, Work with Autel MaxiSYS Elite II, Elite, MS908, MS908S Pro, MS908CV, MK908P, MK908 Pro II and PC
  • 🌐【Works with Autel MK908, MS908(S/Pro), MK908P, MaxiSys Elite】Autel J2534 work with these tools to program ECUs on specific BMW/ BENZ for specific functions. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your scanner MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, contact us via: 🚘auteldirect @ outlook. com🚘.
  • 🌐【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
  • 🌐【High-speed Transmission Speed】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed to save more times and win more business.
  • 🌐【Multiple Devices Connected with PC】Autel MaxiFlash Elite J2534 also supports multiple device connections to the PC, which can operate diagnostic and reprogramming functions on more than one vehicle at the same time. Autel MaxiFlash Elite J2534 built-in wireless and data storage, which can update via Internet. It also ensures quickly reprogramming even the newest controllers.
  • 🌐【Extensive Compatibility】Autel MaxiFlash J2534 is compatible with Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
Bestseller No. 4
LAUNCH X431 PRO5 Elite,J2534 Reprogramming Tool, Topology Mapping OBD2 Scanner Diagnostic Tool, CAN/CAFD/DoIP/HD/FCA SGW,Bidirectional Scan Tool, ECU Coding, 50+ Reset, All Systems Scanner
  • 🆚LAUNCH X431 PRO5 scan tool Upgrade all functions of X431 PRO3/X-431 Throttle III/X431-TorqueIII/X431 V+, PROS V+, PAD3. ⓵ J2534 ECU Programming &Online functions directly connect to OEM server, 50+ reset same as X-431 Throttle;⓶Bi-directional control and All system diagnostics as Snap-on scanner; ⓷ Support 150+ brands Vehicles (include CAN/CAFD/DoIP/HD protocols and AutoAuth for FCA SGW) ⓸Powered by 8-core processor(1.8GHz), Android9.0 OS, 2.4 & 5GHz WiFi connection.
  • 🚜[J2534 Reprogramming With FREE SMARTBOX 3.0】Save more than $2000, LAUNCH X431 PRO5 support J2534/DOIP/CANFD/HD protocols (Needn’t buy HDIII Module,Manufacture software and non-16pin adaptors need to be purchased separately.) Download OEM software from the manufacturer’s server to 1) program data to blank/used ECUs; 2) Reflash ECUs with data loss; 3)Upgrade ECU software version. As a wireless VCI allowing the vehicle to transmit data to the diagnostic tablet without a physical connection.
  • 👏[50+ Reset, Continuously Updated Reset Functions]: With the LAUNCH diagnostic tool, You will never be bothered by tricky vehicle issues and keep pace with newer technology. 50 commonly reset functions ( in the quick page ) reaching into the smallest parts to root out the problems. Extra 300+ repair functions ( in-vehicle catalog) for specific models extend the capability to reset, regeneration, initiation, matching, etc. (Functions vary by models, configurations, and systems.)
  • 🌐[One stop Intelligent Diagnostic Tool]: LAUNCH X431 PRO5 obd2 scanner Bluetooth provides Repair Tips, Repair Assist, Component Measurement, TSB, Relevant Cases DTC Analysis to simplify complex diagnostic and achieve the trouble-free repair. 🤩[One Scanner For Multiple Uses]: LAUNCH diagnostic tool PRO5 collaborates with add-on modules (ADAS, Videoscope, TSGUN, X-ProG3, WiFi Pinter, Battery Tester) to expand business applications and improve diagnostic accuracy.
  • 👍【2024 New OE Level Online Functions 】Bidirectional Scan Tool offers you various high-end online functions, which enable you to access the online data to do fast & complicated vehicle repairs, e.g. 1) ECU Coding for replacing, match, relearn, recode new ECU modules; 2) Online Coding for BMW, Audi, VW, Porsche, Benz to surf OEM data; 3) VAG Guided functions ease complex issues; 4) Personalization & ADAS improving car performance and driving safety.
Bestseller No. 5
Mongoose-Plus J2534 OEM Vehicle Interface Cable - GM OEM Reprogramming and Diagnostics
  • Industry-leading J2534 Pass-Thru Technology: Enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. Economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Each type (see single branded types above) Mongoose-Plus is engineered to work with one of the following OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, Subaru, & VW/Audi.
  • Supports Current GM Vehicles: Now includes CAN-FD, DoIP (Diagnostics over Internet Protocol - as defined in J2534-2) and support for J2534 version 5.0. This is the tool that GM dealerships use for diagnostics and reprogramming.
  • NEW Bluetooth Wireless Options Available: Providing wireless connectivity between your laptop and the Mongoose-Plus
  • Expert Product Support: Staffed by technicians who understand vehicle repair and J2534 Pass‑Thru applications to help you with any technical setup questions
  • Key Registration and Immobilizer Support: Using NASTF Vehicle Security Professional credentials
Bestseller No. 6
Autel MaxiFlash Elite VCI J2534 Pass-Thru ECU Programming Tool, Vehicle Communication Interface,Work with Autel MaxiSYS Elite II, Elite, MS908, MS908S Pro, MK908 Pro II, MS908CV, MK908P and PC
  • 【As a multi-protocol Pass-Thru vehicle interface】MaxiFlash Elite is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device. Specially designed to provide users with convenient PC communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, MaxiFlash Elite offers the most significant features desired by OEM customers: reliability, fast performance and flexibility.
  • 【MaxiFlash Elite is an accessory tool for MK908P, MS908S Pro】Autel MaxiSys Elite to program ECUs on specific for BMW and for Benz vehicles, in case you lost the J-2534 programmer. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your tablet MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. The functions are NOT universally compatible. Please send VIN number to 🚘jmxd2022@outlook.com📧🚘 to check compatibility before your order. If need any supports, Please contact us.
  • 【Wireless with advanced networking functions】Built-In Wireless with advanced networking functions and data storage. Fast performance ensures reprogramming even the newest controllers & Internet upgradable and updatable. Autel MaxiFlash Elite is compatiable with MaxiSYS MS908S, MaxiSYS MS908S Pro , MaxiSYS MS908CV, MaxiCOM MK908, MaxiCOM MK908 Pro, MaxiSYS Elite, MaxiSYS Elite II and Personal Computer
  • 【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
  • 【Supports simultaneous communication Definition in J2534-1】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed.Rugged aluminum case with non-slip rubber end caps, capable of withstanding harsh environment.

Last update on 2024-03-18 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

4 thoughts on “Flash: Transmission Diagnostic and Shift Enhancements – 2015 Jeep Cherokee & Chrysler 200”

  1. I have a vehicle that is listed under this bulletin.my 2015 Jeep Cherokee is having a P0885 code when started. How do I get this problem fixed? And will this be fixed by the dealer for free?

    Reply
  2. had my tcm and pcm flashed last week due to my 2.4l 2015 jeep Cherokee mil light came on due to a bad coil…..mind you the dealer flashed the tcm and pcm change my 4 new plugs that were auto lite platinum…the said that they weren’t oem and that’s what triggered the mil light….so after 494 dollars and 4 hours later they told me jeep was good to go…I had to return to dealer right away due to lack of power and bucking ..they told me coil number 3 was no good and because they keep spares at dealer I’d have to wait 3 weeks for replacement part….fuck it I called Napa had my friend find and get me one next day Christmas eve to note.so now jeep idles smooth but now instead of shifting gears and a little buck from 1st to 2nd and being in 9th at 120kmh 1975rpm it shifts at 3100rpm and is stuck in 7th at 2000rpm I have to play with gas pedal and manual shift it to 8th and 9th but to get it in to 9th I’m hitting 155kmh 3100rpm to get in gear then it play with gas pedal to keep it in 9th as I let vehicle slow to 120kmh…at 2100rpm…
    Main question can I have new updates removed…they suck I could program better than that

    Reply

Leave a Reply to oemdtc Cancel reply

Share to...