Decklid Contacts The Body Side Aperture Above The Stop Lamp – 2015 Dodge Charger

NUMBER: 23-005-15
GROUP: Body
DATE: February 06, 2015

 

THIS SERVICE BULLETIN IS ALSO BEING RELEASED AS RAPID RESPONSE TRANSMITTAL (RRT) 15-018. ALL APPLICABLE SOLD AND UN-SOLD RRT VIN’s HAVE BEEN LOADED. TO VERIFY THAT THIS RRT SERVICE ACTION IS

APPLICABLE TO THE VEHICLE, USE VIP OR PERFORM A VIN SEARCH IN TECHCONNECT. ALL REPAIRS ARE REIMBURSABLE WITHIN THE PROVISIONS OF WARRANTY.

 

SUBJECT:

Decklid Contacts The Body Side Aperture Above The Stop Lamp

 

OVERVIEW:

This bulletin involves adjusting the decklid and touching up paint as required.

 

MODELS:

2015

(LD)

Dodge Charger

 

NOTE: This bulletin applies to vehicles built on or after November 7, 2014 (MDH 1107XX) and on or before November 22, 2014 (MDH 1122XX).

 

SYMPTOM/CONDITION:

The customer may describe contact between the decklid and body side aperture (1) and/or chipped paint (2) on left or right side above the stop lamp (Fig. 1).

 

Fig. 1 Contact Areas And Chipped Paint

1 – Decklid To Body Side Aperture Contact
2 – Chipped Paint

---

DIAGNOSIS:

If a customer’s VIN is listed in VIP or your RRT VIN list, perform the repair. For all other customers that describe the symptom/condition, perform the Repair Procedure.

 

PARTS REQUIRED:

Qty.	Description	Part No.
1 (AR)	PX8 Pitch Black	04342250AB Mopar 04342250AB PAINT ROLLER - DX8 Mopar OEM part that fits your specific vehicle PAINT ROLLER - DX8 Part Number: 04342250AB Manufactured to meet specifications for fit, form, and function $66.64 Buy on Amazon Price incl. tax, excl. shipping
1 (AR)	PW7 Bright White Clear Coat	04889598AB MOPAR 04889598AB - Paint Genuine Mopar part that fits your specific vehicle Touch-Up Paint Pen Part Number: 4889598AC Manufactured to meet specifications for fit, form, and function Buy on Amazon Price incl. tax, excl. shipping
1 (AR)	PAU Granite Crystal Met. Clear Coat	68183829AA MOPAR 68183829AA PAINT $27.83 Buy on Amazon Price incl. tax, excl. shipping
1 (AR)	PBX Jazz Blue Pearl Coat	68183807AA
1 (AR)	PSC Billet Silver Metallic Clear Coat	05163738AA No products found.
1 (AR)	PR3 TorRed	05163108AA
1 (AR)	PXT Phantom Black Tri-Coat Pearl	68183821AA Mopar Phantom Black Tri Coat Pearl - 68183821AA Buy on Amazon Price incl. tax, excl. shipping
1 (AR)	PRY Redline Red Tri-Coat Pearl	05163750AA
1 (AR)	PWD Ivory Tri-Coat Pearl	05163838AA

 

NOTE: Each bottle of touch-up paint will service several vehicles (shop supply).

 

SPECIAL TOOLS/EQUIPMENT REQUIRED:

2022300230

Gauge, Non-Metallic, Clearance Measurement or equivalent non-metallic clearance gauge.

 

NOTE: The Non-Metallic Clearance Gauge is a non-reimbursable shop tool.

 

REPAIR PROCEDURE:

1. Use a 1.75 mm plastic feeler guage or equivalent to measure the gap (1) between the decklid and body side aperture at the points identified in (Fig. 2). The 1.75 mm feeler gauge should slide freely between the decklid and body side aperture without binding or being unable to pass.

Fig. 2 Measure Decklid To Body Side Aperture Gap

1 – Gap Between Gauge And Fender

---

2. Did the 1.75 mm feeler gauge pass freely between the decklid and body side aperture without binding, indicating the gap is at least 1.75 mm or greater?
   • YES>>> This bulletin has been completed, use LOP (23-00-05-91) to close the active RRT.
   • NO>>> Continue with Step #3.
3. Open the decklid.
4. Open the load floor.
5. Pull forward at the bottom of the trunk trim panel (1) to release the lower retaining clips (Fig. 3).
6. Lift the trunk trim panel (1) up to release the upper retaining clips and remove the panel (Fig. 3).

Fig. 3 Remove Trunk Trim Panel

1 – Trunk Trim Panel

---

7. Using a marking pen or equivalent, mark the decklid striker current position (1) (Fig. 4).
8. Loosen the two striker fasteners (2) (Fig. 4).
9. Position the striker (3) approximately 1 mm higher then tighten the fasteners (2) to 8 N·m (52 in. lbs.) (Fig. 4).

Fig. 4 Adjust Decklid Striker

1 – Mark Striker Current Position
2 – Striker Fasteners
3 – Decklid Striker

---

10. After adjusting the striker, ensure the striker does not rub on the decklid latch. Reposition the striker if necessary.
11. Check the decklid to body side aperture gaps/flushness measurements and closing effort. Decklid to body side aperture gap should be 1.75 mm or greater as measured in Step #1 and decklid should be no more than 1 mm over flush in relation to the body side aperture.
12. Did adjusting the decklid striker increase the decklid to body side aperture gap to 1.75 mm or greater without exceeding 1 mm overflush of decklid in relation to body side aperture?
    • YES>>> Proceed to Step #22.
    • NO>>> Continue with Step #13.
13. Remove the push fasteners (1) and the decklid hinge cover (2) ( 5).

Fig. 5 Remove Hinge Covers

1 – Push Fasteners
2 – Hinge Cover

---

14. Loosen the two hinge bolts (1) (Fig. 6).
15. Grasp the decklid with both hands and firmly push up (2) (decklid moves rearward) (Fig. 6).
16. Tighten the two hinge bolts (1) to 14 N·m (10 ft. lbs.) (Fig. 6).

Fig. 6 Adjust Decklid

1 – Hinge Bolts
2 – Move Decklid

---

17. Check that the decklid to body side aperture gap is 1.75 mm or greater as measured in Step #1 and is no more than 1 mm over flush in relation to the body side aperture. Readjust decklid and striker as necessary to achieve the desired fit and spacing between the decklid and body side aperture.
18. Install the decklid hinge cover (2) and push fasteners (1) (Fig. 7).

Fig. 7 Install Hinge Covers

1 – Push Fasteners
2 – Hinge Cover

---

19. Position the top of the trunk trim panel (1) and push down to engage the top retaining clips (Fig. 8).
20. Hand tap the lower edge of the trunk trim panel (1) to engage the lower retaining clips (Fig. 8).
21. Close the load floor cover.

Fig. 8 Install Trunk Trim Panel

1 – Trunk Trim Panel

---

22. If paint was chipped due to contact between the decklid and body side aperture, touch up the paint as required.

Fig. 9 Touch Up Paint Chips

1 – Paint Chips

---

POLICY:

Reimbursable within the provisions of the warranty.

 

TIME ALLOWANCE:

Labor Operation No:	Description	Skill Category	Amount
23-00-05-91	Inspect Decklid To Body Side Aperture Gap (0 – Introductory)	6 – Electrical and Body Systems	0.2 Hrs.
23-00-05-92	Inspect And Adjust Decklid To Body Side Aperture Gap And Touch Up Paint (0 – Introductory)	6 – Electrical and Body Systems	0.3 Hrs.

 

FAILURE CODE:

ZZ	Service Action

 

---

NUMBER: 23-005-15
GROUP: Body
DATE: February 06, 2015

https://www.nhtsa.gov/recalls?nhtsaId=10144820

https://static.nhtsa.gov/odi/tsbs/2015/MC-10144820-9999.pdf

 

---

 

This product presentation was made with AAWP plugin.