NUMBER: 08-036-04
GROUP: Electrical
DATE: October 27, 2004
THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 08-003-03 REV. A DATED APRIL. 4, 2003 WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDES A REVISED PARTS AND MODELS TABLE.
SUBJECT:
Sentry Key – Key Immobilizer Security System
MODELS:
| **2001 – 2005** | (ST) | Sebring/Stratus Coupe |
DISCUSSION:
The Anti-theft engine immobilizer with security key is designed to significantly reduce the possibility of vehicle theft. The system immobilizes the vehicle if an invalid start is attempted. A valid start can only be accomplished by using a key registered to the vehicles electronic immobilizer system.
The immobilizer system consists of the ignition key(s), key ring antenna, immobilizer ECU and Engine Control Module (ECM) M/T or Powertrain Control Module (PCM) A/T models. The ignition key has a built in transponder. The key ring antenna is installed around the ignition key cylinder. The immobilizer ECU and ECM or PCM are located within the instrument panel. If requirements for starting the engine are not satisfied, the engine will start and stall within a few seconds of the first invalid attempt. After the initial start and stall, the engine will not start since the fuel and ignition systems are disabled.
If keys are lost or additional keys are required, they can be registered using the DRBIII® and CH8425 PCMCIA card. The immobilizer ECU can hold up to 8 uniquely coded transponder keys of any master or valet (if applicable) combination. In addition to registering keys, the DRBIII® can be used to read DTC’s for diagnostics and read the number of keys registered for a given vehicle.
NOTE: Keys can only be programmed by using the DRBIII®. This feature for the D.A.R.T. is not available.
If a system failure is detected and the immobilizer ECU or an ECM/PCM require replacement, the only requirement is to re-register keys. If the ECM/PCM or ECU is replaced for any reason, the DRBIII® may not allow key registration due to the immobilizer ECU not recognizing the encrypted code and password from the ECM/PCM. If this occurs, the following steps are required:
- Switch the Ignition key to “OFF” and remove it from the ignition cylinder.
- Remove the DRBIII® from the vehicle.
- Insert the ignition key and switch the ignition to “ON” for a minimum of 30 seconds.
- Switch the ignition key to “OFF” and connect the DRBIII®.
- Boot the DRBIII® with the PCMCIA card and follow Registration Procedure listed below.
PARTS REQUIRED:
| Qty. | Part No. | Description |
| AR | MR558768 | Key 2001, Master Sebring Coupe |
| AR | MR530317
No products found. | Key 2001, Master Stratus Coupe |
| AR | MR515985 | Key 2001, Valet Sebring Coupe/Stratus Coupe |
| AR | MR587241 | Key 2002, Valet Sebring Coupe/Stratus Coupe |
| AR | 05086276AA
Keyless2Go Replacement Uncut Transponder Ignition Car Key Y164 (2 Pack)
| **Key 2002 – 2005, Master Stratus Coupe** |
| AR | 05086275AA
Keyless2Go Replacement Uncut Transponder Ignition Car Key Y164 (2 Pack)
| **Key 2002 – 2005, Master Sebring Coupe** |
NOTE: 2003 and later vehicles do not utilize valet keys.
EQUIPMENT REQUIRED:
| CH6000 | Scan Tool (DRBIII®) |
| CH8425 | ST22 PCMCIA Diagnostic Card |
| CH7010 | J1962 MMC Cable |
REGISTRATION PROCEDURE:
NOTE: For 2001 vehicles, all keys must be available before proceeding.
NOTE: For 2002 or newer vehicles, a new feature was added to the DRBIII® to make key programming easier. Individual keys can be programmed without having the customers remaining key(s).
- Connect the DRBIII® to the vehicle and boot (RUN MEMORY CARD PROGRAM) the PCMCIA card.
- Switch the ignition key to the “ON” position and select SYSTEM SELECT from the main menu.
- From the SYSTEM SELECT menu, select IMMOBILIZER.
- From the SELECT FUNCTION menu, select SPECIAL FUNCTION.
- From the SPECIAL menu, for 2001 vehicles, select 1. REGISTER ALL KEYS. For 2002 or newer vehicles, select 1. REGISTER ALL KEYS or 2. REGISTER INDIVIDUAL KEYS.
- Once the selection is made, the DRBIII® will prompt for a password. Input 6876 to proceed with key registration.
NOTE: If an incorrect password is used 5 times, the immobilizer ECU will switch to an unauthorized operation mode and prevent key registration. The DRBIII® will indicate this by displaying “CANT EXECUTE FOR 20 MIN. DUE TO WRONG PASSWORD”. The ignition key must be left in the “On” position during the 20 minute wait period.
- Follow the remaining prompts on the DRBIII® to complete key registration procedures.
NOTE: If an error occurs during key ID registration, the message “CANT EXECUTE” will be displayed. If the key has already been programmed, “KEY ID HAS BEEN REGISTERED” will be displayed.
- Once all keys have been registered, press the NO key on the DRBIII® to exit the registration menu.
- Switch the ignition key “OFF” for 10 seconds and then check to make sure each key that was registered will start the vehicle.
- If all keys start the vehicle, switch the ignition “OFF” and remove the DRBIII®.
NOTE: 2002 – or newer vehicles provide the customer with the capability to program their own keys. This is only possible if they have two (2) valid programmed keys.
The procedures for customer programming are listed in the Owner’s Manual and follow for your reference:
- Insert the first valid key into the ignition and turn the ignition to the “ON” position for 5 seconds.
- Turn the ignition to the “OFF” position and remove the first key.
- Insert the second valid key into the ignition and switch the ignition to the “ON” position within 7 seconds. The Theft-alarm indicator will blink twice to indicate the system is in programming mode. Turn the ignition to the “OFF” position and remove the second key.
- Insert the cut “Non Programmed” Sentry Key into the ignition and switch the ignition to the “ON” position within 7 seconds of removing the previous key. The theft-alarm indicator will illuminate for about 3 seconds when registration is completed.
NOTE: If an error occurs during programming, the theft alarm indicator will flash three (3) times.
- Repeat step 4 if you want to register additional keys. Make sure the entire registration process is completed within 30 seconds after the theft-alarm indicator flashes in step 3.
POLICY:
Information Only
https://www.techauthority.com/Pdf/SebringStratusCoupeServiceBulletin.pdf
- 【Read Carefully Before Ordering】Batteries Not Included. This is a blank key that must be pr0grammed before use. It works with Thinkcar scan tools like THINKSCAN 689, THINKSCAN 689BT. 【Warm Tips】Dear friend, if you have any issues with product(functions not work, not sure about the compatibility), or just a simple question, please don't hesitate to con.tact us via Amazon Message or directly reach to us via support@ mythinkcar. com. We are committed to ensuring your experience is seamless.
- 【One Solutions Meet All Your Needs】The TKey101 is equipped with four standard anti-the.ft types, supports anti-the.ft data for over 8000 vehicle models, and it's configured with super chips covering more anti-the.ft chips of different car models.
- 【High Sensitivity 3 Buttons】Crafted from premium engineering materials for enhanced durability and drop resistance, this key fob delivers the same performance as the factory original. It features five responsive buttons: L.ock, Unl.ock, and Panic (to locate your car). Do it yourself, it serves as a quick and easy replacement for your lost or broken remote fob. Kindly note: Please ensure that your original remote has the exact same number and layout of buttons before purchasing.
- 【Pr0grammable with Thinkcar Thinkscan Tools】Thinkcar blank key can be pr0grammed for supported vehicles using Thinkscan Tools, including THINKSCAN 689BT, THINKSCAN 689, THINKTOOL series, etc. Please note the compatibility varies by car models, we recommend that you check compatibility with us before purchase.
- 【Package Included】1 * Tkey101 K.ey Progra.mmer, 6 * Universal Remote, 1 * Super Chip, 1 * USB3.0 to TypeC Cable, 1 * Remote Generation Cable, 1 * User Manual.
- 💝【Warm Notice】Starting Q3 2026, Autel KM100(KM100X KM100E) will gradually integrate NASTF SDRM to meet evolving industry standards. Certain vehicle functions may require a VSP credential ($435 for a Primary account, valid for 2 years). This autel obd2 scanner CAN’T work for Benz, for BMW, for Toyota, for Lexus, for GM, for Chrysler, for Ford and for Nissan. Please email you 17 digits VIN to 💌 autelcare @ outlook . com to check compatibility before purchase!
- 🔧 【Lite Version of IM508S & IM608 II – Easy Professional Use】Autel OBD2 Scanner KM100E delivers core functions from higher-end IM508S and IM608 Pro 2 in a more compact and user-friendly design. With intuitive UI and simple navigation, users can quickly complete full operations without complex learning. The handheld experience is smooth and efficient, making advanced functions accessible for both beginners and professionals. Designed to balance performance and usability, it simplifies complex workflows into clear step-by-step operation.
- 🚗 【Wide Compatibility – Broad Makes & Models Coverage】Supports a wide range of makes and models across global markets, covering most mainstream brands and systems. Whether working on common daily-use platforms or advanced systems, KM100E provides stable compatibility and reliable performance. It is designed to reduce tool switching and increase workshop efficiency by handling multiple brands within one device, making diagnostics more convenient and consistent.
- 🔄 【Lifetime Free Updates – Long-Term Value】Professional mechanic scanner KM100E includes lifetime free software updates, ensuring continuous access to the latest system improvements, expanded coverage, and enhanced functions. Users benefit from ongoing optimization without additional subscription costs. This helps maintain long-term usability and keeps the device aligned with evolving vehicle technologies, making it a cost-effective investment for both workshops and individual users.
- ⚙️ 【2.0 VCI200 – Stable Connection & Faster Performance】Equipped with advanced 2.0 VCI200 communication technology, KM100E ensures faster data transmission, stronger stability, and lower latency during operations. It improves communication between the device and vehicle systems, reducing delays and increasing reliability in tasks. This helps solve common issues like unstable connection or slow response, improving overall workflow efficiency in real working environments.
- Vehicle-specific replacement or spare - this keyless entry transmitter looks and functions like the original fob on certain vehicle years, makes, models and configurations
- Do-it-yourself solution - includes a patented programmer that plugs into your OBD II port to setup your new fob in minutes, without expensive dealership programming
- Matches features - this 4-button remote control features lock, unlock, remote start and panic functions
- Important notes - you must have at least one of your original keys or fobs for programming process; only for use on vehicles that came originally equipped with keyless entry
- Ensure fit - Input your vehicle into the garage tool and check Confirmed Fit bar at the top of the page. If there is an “i” in a blue circle, additional verification is needed. Please hover over the "i" to verify fitment notes match your vehicle.
- Compatibility——This device supports for Honda Selected Vehicle, suitable for Smart Key with FCC: KR5V2X/KR5V1X/KR5T44 / KR5V44/ACJ932HK1310A. If you are unsure if your car model is compatible, please contact customer service
- DO IT YOURSELF——You can program your remote by yourself. Just download the APP and the steps are simple, safe and time-saving. Powerful, professional technical support enables programming keys at home and no need to make any appointment
- High Quality——Each device undergoes strict testing before shipment to ensure proper functioning, and the advanced technology used makes the product compact and easy to carry. And the chip has undergone strict technical testing and will not cause harm to the car and keys, making it very safe and secure
- Note——One can set up to 8 keys if your car system has no limit for single car use only. We have a self-made video programming tutorial with a printed instruction manual. Maximizing worry free programming
- Package——This is just a device only that does not include a key. If you need a new key, you will need to purchase it separately
This product presentation was made with AAWP plugin.