DATE: November 14, 2015
HELP USING THE wiTECH DIAGNOSTIC APPLICATION FOR FLASHING AN ECU IS AVAILABLE BY SELECTING “HELP” THEN “HELP CONTENTS” AT THE TOP OF THE wiTECH DIAGNOSTIC APPLICATION WINDOW.
THE wiTECH SOFTWARE IS REQUIRED TO BE AT THE LATEST RELEASE BEFORE PERFORMING THIS PROCEDURE.
Flash: Vehicle Enhancement
This bulletin involves updating the Body Control Module (BCM) software.
|2015||(WK)||Jeep Grand Cherokee|
NOTE: This bulletin applies to vehicles within the following markets/countries: NAFTA.
NOTE: This bulletin applies to vehicles equipped with Daytime Running Headlamps (Sales Codes LM1).
The customer may describe the Daytime Running Lamps (DRL) inoperative. This condition may be more prevalent after DRL bulb(s) have been replaced with an aftermarket bulb.
Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in TechCONNECT, verify no DTCs are set. If DTCs are present, record them on the repair order and repair as necessary before proceeding further with this bulletin.
If the customer describes the symptom/condition listed above, perform the Repair Procedure.
NOTE: If this flash process is interrupted/aborted or failed, the flash should be restarted.
- Reprogram the BCM with the latest software. Help using the wiTECH Diagnostic Application for flashing control modules is available through the wiTECH Diagnostic Application. For instructions select the “HELP” tab on upper portion of the wiTECH window, then “HELP CONTENTS”. This will open the Welcome to wiTECH Help screen where help topics can be selected.
- Turn off the vehicle and let the Communication Buss go to sleep, this may take a few minutes before the Buss goes to sleep. This will cause all active DTC to go stored. Clear any DTCs that may have been set in other modules due to reprogramming. The wiTECH application will automatically present all DTCs after the flash and allow the tech to clear them.
Reimbursable within the provisions of the warranty.
|Labor Operation No:||Description||Skill Category||Amount|
|18-19-02-BA||Module, Body Control – Reprogram (1 – Semi-Skilled)||6 – Electrical and Body Systems||0.2 Hrs.|
NOTE: The expected completion time for the flash download portion of this procedure is approximately 4 minutes. Actual flash download times may be affected by vehicle connection and network capabilities.
The dealer must choose which failure code to use. If the customer came in with an issue and the dealer found updated software to correct that issue, use failure code CC, for all other use failure code RF.
- If the customer’s concern matches the SYMPTOM/CONDITION identified in the Service Bulletin, failure code CC is to be used.
- If an available flash is completed while addressing a different customer concern, failure code RF is to be used.
Chrysler Recommended J2534 Devices
|J2534 Device||Firmware Version|
|CTC Vehicle Box *||1.9|
|Blue Streak -2534 Global Programmer||2.10|
|Actia I+ME Passthru||2.07|
* Chrysler recommends the CTC Vehicle Box Device for Chrysler SCI ECU reprogramming. SCI reprogramming is used on most PCMs and TCMs prior to the introduction of CAN bus vehicles which began in 2004 (Durango).
Compatible J2534 Devices
Click on the link below to:
Download J2534 Application
(Install the wiTECH 2.0 J2534 Application on your computer)
Download the Setup Utility
(Configure your microPod/MDP device)
Launch wiTECH 2.0
(Once subscription and users are assigned to a tool please follow this link to access wiTECH)
- 👍【Works with Autel MK908, MS908(S/Pro), MK908P, MaxiSys Elite】Autel J2534 work with these tools to program ECUs on specific BMW/ BENZ for specific functions. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your scanner MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, contact us via: 🚘auteldirect @ outlook. com🚘 !
- 👍Fully compatible with both SAE J2534-1 and J2534-2 reprogramming standards and performs standard Pass Thru J2534 functionality. To check compatibility, please contact🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
- 👍Compatible with Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
- 👍Built-In Wireless with advanced networking functions and data storage. Fast performance ensures reprogramming even the newest controllers & Internet upgradable and updatable.
- 👍Attention: 1. After you ordered and received the J2534, please send us both of the S/N(12 digits, at the back of the device) of the J2534 and your MK908(P) /MS908S (Pro)/ Maxisys Elite to us to bind the two device together. 2. The functions are NOT universally compatible. Please send VIN number to 🚘auteldirect @ outlook . com🚘 to check compatibility before your order.
- ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
- J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
- TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
- J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
- FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
- Industry-leading J2534 Pass-Thru Technology: Enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. Economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Each type (see single branded types above) Mongoose-Plus is engineered to work with one of the following OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, & VW/Audi.
- Supports Current & Earlier Vehicles: Enables diagnostics, programming and other “dealer” functions through OEM applications
- NEW Bluetooth Wireless Options Available: Providing wireless connectivity between your laptop and the Mongoose-Plus
- Expert Product Support: Staffed by technicians who understand vehicle repair and J2534 Pass‑Thru applications to help you with any technical setup questions
- Key Registration and Immobilizer Support: Using NASTF Vehicle Security Professional credentials
- [J2534 COMPLIANT] - The Mastertech II is a J2534-1 and J2534-2 compliant VCI for OEM reprogramming and diagnostic applications
- [FULLY VALIDATED BY TOP 6 OEMS] - Mastertech II has been fully validated to operate with the top 6 OEM reprogramming applications: GM, Ford, FCA, Nissan/Infinity, Honda/Acura, and Toyota/Lexus
- [PRE-CONFIGURED] - The pre-configured wireless and wired connections make it quick and easy to connect to a vehicle from your PC (requires PC compliant with OE specifications and software)
- [RIGHT TO REPAIR] - Supports 'Right to Repair' (R2R) initiatives
- [COMPREHENSIVE KIT] - Kit includes: VCI, WiFi adapters (wireless PC to VCI), J1962 Cable (connect to vehicle), USB cable (connect to PC for firmware updates and setup), and Quick Start Guide
- VXDIAG SVCI J2534 can compatible with SAE J2534-1 and partly compatible with SAE J2534-2. It supports most of vehicle communication protocols and can be used as PassThru device for many dealer level diagnostic software. And it can be used as a ELM327 device also, support most of ELM327 software.
- High speed host communication and Stable host communication. (with RTS/CTS flow control).Host communication is high-speed and stable, keeping the diagnosis smooth. And the programming function requires the original online account .（Not work for the Ford F serial cars, like F150,F250,F350,F450）
- [Switch on the Interface] There is a switch button on the interface. Please do press the switch button for the Module you want enter in. Pressed: works as ELM327 mode Released: works as J2534 mode
- VXDIAG SVCI J2534 is compatible with Ford / Mazda IDS,Only need to do two steps to Installs software. First,Install FVDI J2534 start software,then install the original brand vehicle software,For example, Ford, Mazda.(Before install the software,pls turn off your antivirus software )
- For software installation, please feel free to contact our online customer service.
- 👍【Why Choose LAUNCH X431 PRO5】It is the original LAUNCH X431 scan tool, not a copy machine, also the 2022 upgraded version of CRP909X, PROS V1.0, X431 PRO3 and V+. LAUNCH X431 PRO 5, all is set to OE-level standards with 1) J2534 ECU Programming & 50+ service same as PAD V; 2) Bi-directional control + All system diagnostics as Snap-on scanner; 3) Online functions directly connect to OEM server; 4) support 150+ brands Vehicles from 1996-2022.
- 👍【J2534 Programming with Smart Box 3.0】 What is super SmartBox 3.0 VCI? Worth 1000$, Smart Box 3.0 is backed on new J2534/CANFD/DOIP, which enables you to run 14x quicker data trans and advanced OEM J2534 reprogramming for BMW, Benz, Ford, Jaguar, Land Rover, GW, Volvo, etc. (please reach to us for more details). It also serves as a wireless VCI allowing the vehicle to transmit data to the diagnostic tablet without a physical connection.
- 👍【LAUNCH X431 PRO5 with Powerful 50+ Services】Especially designed for pro mechanics and big repair shops, Launch X431 scanner PRO5 is equipped with 50+ hot reset functions for 150 car makes which same as X431 PAD V. Easy to navigate and help you do ABS Bleeding, TPMS Reset, Oil Reset, EPB Reset, Suspension, BMS, Injector Coding, IMMO, Power balance, Throttle Matching and more. 🚩Notice: we offer 2-year free update while other brands generally 1 year.
- 👍【Active Test + Local-smith Level ECU Coding】Come with appealing bi-directional control to troubleshoot all possible problems for full systems within 5 minutes. This LAUNCH scanner even develops all practical functions needed by all technicians: 1) ECU Coding for replacing, match, relearn, recode new ECU modules; 2) Online Coding for BMW, Audi, VW, Porsche, Benz to surf OEM data; 3) VAG Guided functions ease complex issues; 4) Personalization & ADAS improving car performance and driving safety.
- 👍【All System Diagnostics for 99% Vehicle Coverage] Serve for 150+ American, Asian, European brands, and cover 99% of vehicle models worldwide. This LAUNCH diagnostic scan tool can operate complete full-function diagnostics to all on-board systems to troubleshoot and repair all vehicle problems, including Engine, Transmission, Airbag, ABS, ESP, TPMS, Immobilizer, Gateway, Steering, Radio, Air Conditioning, etc.
- 🚗【Same as MaxiSys Elite, No IP Restriction】: Covering 99% of the vehicle models from 1996 to 2022. Based on the MS908S Pro, Autel MK908P diagnostic scan tool enjoys superior hardware configuration, serves 13 languages with no IP restrictions (MS908S Pro ONLY supports English) Lifetime after-sales service and professional technology support have no difference from offline retail version. Feel free to message us with any problems.
- 🚗【ECU Programming & Coding, Guru for Local Smith】: To broaden vehicle business and increase your revenue, the Autel scanner MK908P assigns advanced ECU programming and coding to 1) customize your car, 2) unfold the hidden features, 3) disable the annoying functions to improve car performance, but also reprogram the adaptive data to certain components after repairs or replacements. The specific operation varies by model.
- 🚗【36+ Service Functions, Best for Repair Shops】: Designed for large-scale garages and equipped with 36+ repair functions, Autel MK908P covers 99% of cars in the market. This make it the most valuable scanner to serve as many cars as possible in your shop. The 36+ functions include Oil Reset, TPMS, ABS Bleeding, EPB, SAS, Injector Coding, BMS, Suspension, etc. Please be noted MK908P programming tool will always keep pace with newer functions and continuous upgrading, never out of date.
- 🚗【High-end Online Functions, OE-level Auto Scanner】: MK908P diagnostic tool explores all the systems and scans hidden DTCs. For quickly locating the fault, active test sends commands directly to vehicle modules to perform specific tests on windows, sunroofs, wipers, relays, injectors, and actuators, etc. Newly launched online functions obtain the online data from the server like online account login service for VW, Audi, Skoda; online configuration for Renault; online coding for Porsche; etc.
- 🚗【Top-end Configuration, Ultra-Fast Speed】: Same functions with MaxiSys Elite, but configured with 2G+64G memory Hexa-core processor, 10.1” screen, and 15000mAh battery to accelerate diagnostics and repair. 2022 MK908P diagnostic scanner offers more to expand the market and raise income for example power balance for Ford, Chrysler, GM; personalization for VW, Audi, Toyota; guided functions for VW, Audi, Skoda; etc.
- 🎁【Free OBD2 Scanner】: Just click "Extra Savings" under price and add both to your cart to get a Code Reader. Limited quantity. First come, first served.
- 👍【 ✅More Faster, More Powerful, More Popular, Wider Regional vehicle coverage than Other Similar Diagnostic Tool】This scan tool adds loads of OE-Level features as ➤【AutoAuth for FCA SGW】which makes PD8 works with Chrysler,Dodge,Jeep,Alfa Romeo and Fiat after 2017.➤Setting & Changeover (adblue reset, unlock the engine after a collision, cancel ABS driving test, and more) for Benz ➤Modification for BMW ➤Offline Coding ➤Customization ➤Personalization, for worldwide vehicles, and keep growing.
- 👍【Bi-Directional +Active Test + ECU Coding+Over 34 Reset Services+Adaptation+ Initialization + Matching】Besides actuate solenoids and actuators for active testing. This car scanner diagnostic tool also support : Auto VIN Detect, ECU Coding, Adaptation , Matching ,Key programming,Gear/SAS/EPB/TPMS/DPF/IMMO/BMS/ETS/Oil/Brake/AFS/EGR/GEARBOX/SUNROOF/SUS Reset, ABS Bleed, Injector coding .Gives you the ability to use dealership level relearn procedures to complete repairs or maintenance.
- 👍【Full System Diagnostics + Quick Update Frequency】 This diagnostic scanner can perform OE-level diagnosis and analysis on all available systems: ECM, TCM, ABS, SRS, BCM, BMS, TPMS, and A/C system, etc. Through reading/erasing codes, viewing live data, retrieving ECU info, and performing active tests & service functions, this diagnostic tool evaluates the car’s health status for 100000+ models. With quick update frequency, you can update it once a week to cover newer models.
- 👍【Covering 99.99% Vehicles on world + Better Hardware + Extension Modules】This scan tool works on ECU of vehicles covering Asian, European, American, Russia, Malaysia, India car brands up to 150, 10000 car models . It has optimized with Android 10.0 OS for quick processing & extendable 128GB memory to save data. Also, it supports extended modules (SOLD SEPARATELY): ✅ oscilloscopes; ✅endoscopes; ✅battery detectors✅thermal imaging. All make it much more accurate to fix various models.
- 🥇【LAUNCH X431 PAD VII, 2022 Top Diagnostic Scanner】 As the latest all-around scan tool, LAUNCH X431 PAD VII has upgraded on top of LAUNCH X431 V+/PAD V/PADIII to rival the OEM automotive scanner. Owing ecu programming & online coding, J2534/RP1210/D-PDU/Do-IP/CANFD diagnostic protocols, topology map, 50+ service functions, 2022 advanced functions, highest hardware configuration, and 99.99% vehicles coverage, LAUNCH X431 PAD VII is a worthwhile investment for repair shops and mechanics.
- 【Online Programming & ECU Coding】 LAUNCH X431 PAD VII diagnostic tool with Smartlink C can perform ECU coding & programming to get the car to work correctly after module replacement. They support multiple protocols: J2534 (diagnose vehicles with OEM software and VCI), RP1210/D-PDU (diagnose heavy trucks (the diagnostic software and a non-standard 16PIN connector sold separately), Do-IP (diagnose E and F Chassis BMWs and new cars from Land Rover/Jaguar), CAN FD (diagnose new vehicles from GM).
- 【LAUNCH X431 PAD VII, 50+ Services & Topology Map】 LAUNCH X431 PAD VII bidirectional scan tool has 50+ maintenance functions, including but not limited to oil reset/ABS Bleeding/Injector Coding/AdBlue reset, helping you win more business. With topology map function, you can check the DTCs and all systems communication status visually in LAUNCH X431 PAD VII top obd2 scanner. The actuation test enables the tablet to output commands to the ECU to determine the integrity of systems or parts.
- 【Intelligent Diagnose & Guided Functions】 LAUNCH X431 PAD VII scan tool aims at freeing mechanics from tedious works. Intelligent Diagnose can easily get the VIN information of the car, guide you to vehicle information page without step-by-step selection, and display all diagnostic records. Guided Function (for V.A.G) enables you to follow the on-screen prompts, simple & convenient. Pin Detection allows you to detect the voltage of DLC pins and supported protocol types to troubleshoot the DLC.
- 【All-in-One Tool for Diagnoses and Inspections, Save $2000+】 LAUNCH X431 PAD VII supports add-on modules (sold separately) to carry out more in-depth inspections and calibrations: oscillograph, sensor, battery test, endoscope, Wi-Fi printer, TSGUN, Immobilizer,etc. With 60+ advanced functions: guided functions, component matching, power balance, online parameterization, online calibration, LAUNCH X431 PAD VII high-end comprehensive diagnostic scan tool turns you into a pro auto mechanic.
- 👍【2022 Newest Updates: AutoAuth Access & Cloud Service】Two long-awaited features for old customers!✅(Since June 2022)Autel original MS908S Pro scanner supports "AutoAuth" gateway access on 2018 and newer Fiat Chrysler vehicles, such as Chrysler, Dodge, Jeep, etc, still growing. ✅(Support Cloud Report Management, you can upload diagnostic reports to Autel Cloud and share reports with your customers through QR Code/email/text message easily, and they can view the reports anytime.
- 👍【A Must for Garage and Workshop】If you need to program Benz/BMW, Autel MS908S Pro scanner is definitely an expert, this is what it does best! MS908S Pro is a mature product that has been tested and approved by workshops across US. Besides ECU Programming for Benz/BWM, MS908S Pro can perform ECU Coding, Active Tests, 36+ Services, All System Diagnostic, FCA “AutoAuth” Access, etc.🚦📢👉 Note: MS908S Pro is for North & South America only and supports English only.
- 👍【One-Stop ECU Programming for BENZ/ BMW】Coming with J2534 ECU programming device, Autel MS908S Pro is competent for ECU programming and ECU coding/ adaption. It can program blank ECU, adapt existed ECU, match components, reflash second-hand ECU, unlock hidden functions, etc. In order to reduce operational burden, MaxiSys MS908S Pro provides one-stop operation to meet the needs of different experienced technicians, no worries about missing some steps and causing failure.
- 👍【Advanced ECU Coding, Customize your Car】Automotive diagnostic scan tool MS908S Pro features Advanced ECU Coding, so you can use it to customize your car as needed by disabling some unneeded OEM settings (like auto start-stop, chimes, etc), or activating the hidden features pre-programmed to car computer to get high-end functions (like US-style daytime light, auto door look at a particular speed, etc).👉Compatible with BWM, VW, Audi, Skoda, etc.
- 👍【OE-level Diagnostic Capability & Guided Function】Auto diagnostic tool MS908S Pro, with J2354 device for BT communication up to 210ft/70m working range, can access all available vehicle modules such as PCM, ECM, TCM, BCM, SCCM, etc, to read codes, clear codes, view live data, perform active tests, etc. Guided functions provides step by step specific guidances to complete some complex service operations. 👉Compatible with VW, Audi, Skoda, Seat, etc.
Last update on 2022-08-14 / Affiliate links / Images from Amazon Product Advertising API
This product was presentation was made with AAWP plugin.