Lift Kits May Be Installed with Wrong Size Tires – Rubicon Express 4.5″ & 5.5″ Super-Flex Suspension Lift Kits

July 8, 2020 NHTSA CAMPAIGN NUMBER: 20E047000

Lift Kits May Be Installed with Wrong Size Tires

Reduced vehicle stability from installing 40″ tires can increase the risk of a crash during certain emergency maneuvering situations.

 

NHTSA Campaign Number: 20E047

Manufacturer TAP Worldwide, LLC

Components TIRES, SUSPENSION

Potential Number of Units Affected 22

 

Summary

TAP Worldwide, LLC (TAP) is recalling certain Rubicon Express 4.5″ and 5.5″ Super-Flex suspension lift kits, part number JT7147, sold for installation on 2020-2021 Jeep Gladiator vehicles. The fitment guide for the lift kits may have inaccurately stated that 40″ tires are compatible with the kit, however, installation of 40″ tires can affect vehicle stability in certain emergency maneuvering situations.

 

Remedy

TAP will notify owners, and will replace the fitment guide and if necessary, will replace 40″ tires with tires of an appropriate size, free of charge. The recall began September 2, 2020. Owners may contact TAP customer service at 1-888-376-1417.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 

---

Revised
6.30.20

INSTALLATION INSTRUCTIONS FOR:
JT7099
2020+ 5.5” JEEP GLADIATOR JT SPORT COIL SPRING LIFT KIT
2020+ 5.5” JEEP GLADIATOR JT OVERLAND COIL SPRING LIFT KIT
2020+ 4.5” JEEP GLADIATOR JT RUBICON COIL SPRING LIFT KIT

 

This kit has been approved for 37” and 38” tires.

 

Safety Warning:

Suspension systems or components that enhance the off-road performance of your vehicle may cause it to handle differently, on and off-road, than it did from the factory. Care must be taken to prevent loss of control or vehicle rollover during sudden maneuvers. Failure to drive the vehicle safely may result in serious injury or death to driver and passengers. We recommend you always wear your seatbelt, drive safely and avoid quick turns and other sudden maneuvers. Constant maintenance is required to keep your vehicle safe. Thoroughly inspect your vehicle before and after every off-road use.

 

Installation Warning:

We recommend that certified technicians perform the installations of our products. Attempts to install these products without knowledge or experience may jeopardize the safety of the vehicle. These instructions only cover the installation of our products and may not include factory procedures for disassembly and reassembly of factory components. Read instructions from start to finish and be sure all parts are present before disassembling the vehicle. Included instructions are guidelines only for recommended procedures and in no way are meant to be definitive. Installer is responsible to insure a safe and controllable vehicle after performing modifications. Do not perform test drives on public roads with partially completed installations. Always double and triple check your work before use.

 

ESP WARNING NOTE: The 2020+ Jeep Gladiator JT is equipped with an Electric Stability Program (ESP). This system is designed to help control the vehicle in times of uncertain traction conditions and roll stability. Due to the complex nature of this program Rubicon Express strongly suggest that after lifting the vehicle it is returned to the dealer for a computer “flash” to re address tire size and proper ESP control settings. Rubicon Express also recommends that you become familiar with the ESP controls and how the different level of settings can help you to keep better control of your vehicle. NOTE: Net lift varies with use additional accessories.

 

REQUIRED TOOLS:

Basic mechanics’ hand tools

Vehicle Hoist

Jack Stands

Floor Jacks

 

 JT7099 Jeep JT 4.5”-5.5” 4 Door Universal Kit (w/o Shock):

2	RE1301 2” Front lower bump stop kit
2	90-RM42520 2” Front bump stop spacer
2	31-RM24428 Washer: 3.0” X .43” X .375”
1	HWC15057 Hardware pack, Front bump stops
2	3/8”-16 X 2 3/4” hex bolt gr. 8
2	3/8”-16 Nylon flange nut
4	3/8” Hardened flat washer
1	RE1305 2” Rear bump stop pad
2	90-6513 Hardware Pack, Bump pad
4	5/16”-18 X 1” Hex bolt Gr. 8
4	5/16”-18 Stover nut
8	5/16” Hardened flat washer
2	90-RM24437 2” Rear bump stop extension
1	RE1614 Rear track bar bracket
1	90-2049 Spacer
1	HWC15066 Hardware pack,
3	1/2”-13 X 1 1/4″ Hex bolt Gr. 8
3	1/2”-13 Stover nut
6	1/2” Hardened flat washer
2	9/16”-12 X 3 1/2″ Hex bolt Gr. 8
2	9/16”-12 Stover nut
4	9/16” Hardened flat washer
1	86-RM24433 Rear track bar bracket
1	RE1306 Bump stop extension
2	90-RM42505 1.25” Bump stop extension
1	HWC15065 Hardware pack, Bump stop extension
2	3/8”-16 X 1 1/2” hex bolt gr. 8
2	3/8”-16 Nylock nut
4	3/8” Hardened flat washer
1	HWC15080 Hardware pack, Bump stop extension
2	3/8”-16 X 3 3/4” hex bolt gr. 8
2	3/8”-16 X 4 3/4” hex bolt gr. 8
2	3/8”-16 X 5 3/4” hex bolt gr. 8
1	RE2101 Carrier Bearing Spacer
3	31-RM24490 Carrier Bearing Spacer: .19” Jeep JT
1	HWC15078 Hardware Pack: Carrier Bearing Jeep JT
2	35-RM10050 10mm Flat Washer
2	35-RM14056 10mm-1.5 X 40mm Hex Bolt Gr. 10.9
1	RE1158 Rear Sway Bar Links
4	RM40010 Hourglass Bushing
2	RM11050 Rear Sway bar Link
4	51792 Sleeve 5/8” x 1/2” X 1.37
1	RE1147 Rear Sway Bar End Link Kit
2	91-2311 Sway bar End Link
4	RM40010 Urethane Bushing
4	60859H Sleeve
2	90-6803 Hardware Pack,
1	12mm-1.75 X 65mm Hex bolt Gr. 10.9
1	12mm-1.75 Stover nut
2	12mm Flat washer
2	90-60768 Sleeve: .688” X .558” X 1.525”

 

 Parts used in Conjunction With This Kit (Sold Separately)

1	RE1330 4.5”/5.5” Front coil springs
2	RM60168 4.5”/5.5” Front coil spring
2	RM43013 Coil Shim
1	RE1331 3.5”/4.5” Rear coil springs
2	RM60167 1.5”/2.5” Rear coil spring
1	RE1689 HD Track bar
1	RE1883-385 JK/JL/JT Front Driveshaft 38.5”
1	RE1810 JK/JL/JT 1310 Yoke Adapter
1	RE1521 JT Rear Brake Line Kit
1	RE1518 JL Rubicon Front Brake Line Kit

 

Rear Installation:

1. Prepare for the rear installation by removing the following items from the rear of the vehicle: tires/wheels, shocks, sway bar end links, emergency brake cable clamp (on top of differential), frame mount brake line bracket, and the track bar. Loosen the rear control arm bolts at the frame to let the axle droop.
2. With the items removed, carefully lower the rear axle assembly and remove the coil springs from the vehicle. Note the position and orientation of the upper coil spring isolators, they will be reinstalled with the new coil springs.

NOTE:  Be careful not to overextend the rear brake lines.

3. Remove the OE rubber coil divider and install onto the fourth coil down from the top, on the replacement rear coil springs, PHOTO #2
4. Slide rear track bar bracket, 86-RM24433, over the rear axle track bar mount. Using the 9/16” X 3 1/2” bolt and hardware, sleeve, 90-2049, bolt the track bar bracket to the axle. Be sure the head of the lower 9/16” bolt is facing toward the front of the vehicle for optimal coil clearance.
5. Using the rear track bar bracket, 86-RM24433, as a template, drill 1/2” holes on the front and rear of the OE track bar bracket. Install the supplied 1/2” X 1 1/4” bolts and hardware from pack HWC15066.  Loosely install the track bar into the rear track bar bracket using the supplied 9/16” hardware and the head of the bolt facing the rear of the vehicle. At certain pinion angles the coil spring clearance to the bottom 9/16” bolt can be tight.  Flip the 9/16” bolt if necessary.  PHOTO #1
6. Install the replacement rear coil springs, in place of the previously removed stock coil springs. PHOTO #2

7. Raise the axle into place and install the new rear shocks or shock extensions. Shock sleeves, 90-60768B, have been provided with the kit for use with, RXT2810B shocks or RXJ907   Press the sleeves into the bushings before installation

NOTE: If the suspension kit was purchased with Rubicon Twin Tube shocks, you will need to install shocks on the vehicle with the body down. 

NOTE: If the suspension kit was purchased with Rubicon 2 1/2” shocks, be sure the Schrader valve is oriented toward the rear of the vehicle.

8. Install the replacement rear anti-sway bar end links, RE1147, in place of the previously removed factory anti-sway bar end links as follows:
9. Secure to the frame using the previously removed OE hardware. Torque OE bolt to manufacturer’s specifications. Secure the sway bar to the end link using the supplied 12mm X 65mm bolts and hardware. Be sure the head of the bolt is facing toward the outside of the vehicle. Torque the 12mm bolts to 60 ft.-lbs. PHOTO #3

NOTE: It may be necessary to drill sway bar mounting holes out to 1/2”.

9. Install the 2” rear bump stop pads, RE1305 to the rear axle, with the “F” arrow pointing towards the front of the vehicle, using the supplied 5/16” X 1” bolt and hardware. If 37” tires are being installed on any edition other than a Rubicon, bump stop extensions, RE1306, will need to be bolted to the 2” rear bump stop pads center hole using the supplied 3/8” X 1 1/2” bolt and hardware. PHOTO #4.

(Photo #1)

 

(Photo #2)

 

(Photo #3)

 

(Photo #4)

 

10. Replace the rear brake lines by installing brake line kit, RE1521, following the instructions provided with the kit.
11. Reinstall the emergency brake cable clamp and frame mount brake line into the original position.
12. Reinstall the rear wheels and check the torque on all nuts and bolts.
13. Re-connect the frame end of the track bar with vehicle on the ground and at ride height. Tighten the 9/16”

NOTE: If installing rear adjustable track bar, RE1676, do so at this time following the instructions provided with the kit.

14. Adjust the position of the brake lines, breather hoses, and ABS lines as required.
15. Install (3) carrier bearing spacers, 31-RM24490, from kit, RE2101, using the supplied 10mm x 40mm bolts and washers.
16. If installing adjustable rear upper control arms, RE3726, and adjustable rear lower control arms, RE3727, do so at this time following the instructions provided with the kits.
17. With the vehicle on the ground, tighten the OE rear control arm bolts at the frame. Torque the OE bolts to manufacturer’s specifications.

 

Front Installation: 

1. Prepare for the front installation by removing the following items from the front of the vehicle: tires/wheels, shocks, and sway bar end links. If necessary, support front axle with jack.  Disconnect the front driveshaft U-joint from the axle to prevent damaging the CV when installing the springs.

NOTE: Disconnecting the front track bar may assist in front coil removal/ installation.

2. Remove the ABS/4×4 wire from the passenger side upper arm pivot at the axle.
3. With the items removed, carefully lower the front axle assembly and remove the front coil springs.

NOTE: It may be necessary to disconnect brake line brackets from front control arms to prevent over extending the front brake lines.

(Photo #5A)

 

(Photo #5B)

 

4. For proper bump stop height, install front bump stops as follows:

NOTE: Washers and nuts will be sourced from kits, RE1301 or RE1306, and remove the brake line bracket from the coil bracket to install the bump stops.

1. Rubicon Edition with 38” tires or all other editions with 35” tires: Install (1) 1 1/4”  bump stop extensions, 90-RM42505, from bump stop kit, RE1306 and (1) 2” poly bump stop spacer, 90-RM42520, from bump stop kit, RE1301 inside the coil per side. This configuration will be secured with the 3/8” X 3 3/4” bolt and hardware.  PHOTO #5A.

NOTE: Using less than 3 1/4” of total bump stop spacer/extension height can damage shock.

1. Non-Rubicon editions installing 37” tires: Install (1) 3/8” steel spacers from kit, RE1301, and (2) 2” poly bump stop spacers, 90-RM42520, inside the coil per side. This configuration will be secured with the 3/8” X 4 3/4” bolt and hardware. PHOTO #5B.

5. To install the coil spring, one side at a time, unbolt and remove the lower control arm from the axle mount.
6. Install the coil shim, 90-RM43013, on the passenger side, on top of the OE coil isolator. With the correct amount of lower bump stops and spacers (Refer to Step 3), placed inside the new front coil springs, RM60168 (Sold Separately), raise the small diameter end of the coil springs into the upper spring buckets and over the lower spring cups and bump stop pads. Rotate the coil springs so the end of the coil properly sits in the factory isolators. Secure lower bump stops using the supplied 3/8” bolts and hardware depending on the bump stop height (Refer to Step 3).  PHOTOS #5A, 5B         

NOTE: Be sure not to overextend any brake lines or wires when installing the coil springs.

7. If installing adjustable front lower control arm kit, RE3722, or geometry correction brackets, RE9801, do so at this time following the instructions provided with the kits.
8. Install the replacement front shocks in place of the previously removed stock shocks.
9. Raise the axle into place and install the front sway bar end links, RE1158, in place of the previously removed factory anti-sway bar end links and secure to the sway bar and front axle using the supplied 1/2” X 2 1/2” hex bolts and hardware. If installing adjustable sway bar link kit, RE1136, do so at this time following the instructions provided with the kit. PHOTO #6

NOTE: It may be necessary to drill sway bar mounting holes out to 1/2”.  NOTE: Front sway bar end links, RE1158, can be discarded if adjustable sway bar link kit, RE1136, is installed.

10. Re-connect track bar if disconnection was required.
11. Unbolt and remove OE front driveshaft. Save the OE hardware for reinstallation.
12. Install the front driveshaft coupler, RE1810, following the instructions provided with the kit.

(Photo #6)

 

13. Install the front driveshaft, RE1883-385, following the instructions provided with the kit.
14. Replace the front brake lines by installing brake line kit, RE1518, following the instructions provided with the kit.
15. If installing adjustable front upper control arms, RE3723, do so at this time following the instructions provided with the kit.
16. Reinstall the front wheels and check the torque on all nuts and bolts.

 

Installation review:

1. Torque all the bolts to factory specifications. Be sure to double check your work.
2. Check steering and suspension in all positions to ensure that there is no bind and adequate clearance between all moving, fixed, and heated members.
3. Test drive and note the location of the steering wheel.
4. Adjust the drag link to center the steering wheel if necessary.
5. Align the vehicle as soon as possible. Set to minimum factory caster angle and factory toe-in specifications.
6. Recheck all bolts after 50 miles and again after every off road excursion.

 

Application information:

• Rubicon Edition: This kit is designed for the use of up to 38” diameter tires or smaller on Rubicon Edition Vehicles. To have full tire clearance, the corners of the upgraded OE winch capable steel bumper (MC6) must be unbolted. An aftermarket bumper is another alternative, but clearance should be checked during installation. Washers can be installed behind the OE steering stops to prevent the tires from rubbing.  Check all steering clearances at full lock throughout travel before driving.
• All Other JT Editions: This kit is designed for the use of up to 37” diameter tires or smaller on the Jeep JT Sport and Overland Editions. If 35” or 37” tires are to be installed, it is recommended to use 35”/37” X 12.50” tires on an 8”- 9” wide wheel with a 75” backspace. 37” tires will require an aftermarket bumper for turning clearance.

 

RUBICON EXPRESS ADVANTAGE LIFETIME WARRANTY

 

Notice to Owner, Operator, Dealer and Installer:

Vehicles that have been enhanced for off-road performance often have

unique handling characteristics due to the higher center of gravity and larger tires. This vehicle may handle, react and stop differently than many passenger cars or unmodified vehicles, both on and off– road. You must drive your vehicle safely! Extreme care should always be taken to prevent vehicle rollover or loss of control, which can result in serious injury or even death. Always avoid sudden sharp turns or abrupt maneuvers and allow more time and distance for braking! Rubicon Express reminds you to fasten your seat belts at all times and reduce speed! We will gladly answer any questions concerning the design, function, maintenance and correct use of our products.

 

Please make sure that the Dealer / Installer explains and delivers all warning notices, warranty forms and instruction sheets included with Rubicon Express product.

 

Application listings in this catalog have been carefully fit checked for each model and year denoted. However, Rubicon Express reserves the right to update as necessary, without notice, and will not be held responsible for misprints, changes or variations made by vehicle manufacturers. Please call when in question regarding new model year, vehicles not listed by specific body or chassis styles or vehicles not originally distributed in the USA.

Please note that certain mechanical aspects of any suspension lift product may accelerate ordinary wear of original equipment components. Further, installation of certain Rubicon Express products may void the vehicle’s factory warranty as it pertains to certain covered parts; it is the consumer’s responsibility to check with their local dealer for warranty coverage before installation of the lift.

 

Warranty and Return Policy:

Rubicon Express warranties its full line of products to be free from defects in workmanship and materials for the life of the product. Rubicon Express’s obligation under this warranty is limited to repair or replacement, at Rubicon Express’s option, of the defective product. Any and all costs of removal, installation, freight or incidental or consequential damages are expressly excluded from this warranty. Rubicon Express is not responsible for damages and / or warranty of other vehicle parts related or nonrelated to the installation of Rubicon Express product. A consumer who makes the decision to modify his vehicle with aftermarket components of any kind will assume all risk and responsibility for potential damages incurred as a result of their chosen modifications.

 

Warranty coverage does not include consumer opinions regarding ride comfort, fitment and design. Warranty claims can be made directly with Rubicon Express or at any factory authorized Rubicon Express dealer.

 

Claims not covered under warranty:

• Parts subject to normal wear; this includes bushings*, shock absorbers, driveshafts, ball joints, tie rod ends and heim joints.
• Discontinued products at Rubicon Express’s discretion.
• Finish after 90 days.

Rubicon Express accepts no responsibility for any altered product, improper installation, lack of or improper maintenance or improper use of our products.

 

*Rubicon Express PT-MEG Super-Ride bushings are covered by the Rubicon Express Advantage Lifetime Warranty, and will be replaced in the event of failure for the life of the product.

 

---

IMPORTANT SAFETY RECALL

This notice applies to equipment you have purchased 

 

Recall Campaign: 20E047
Subject: 2020 Jeep Gladiator Rubicon
Edition 4.5/5.5” Suspension Lift Kit

PLEASE READ IMMEDIATELY

 

 

FIRST NAME  LAST NAME
ADDRESS
CITY, ST ZIP

 

Dear Valued TAP Customer:

This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. TAP Worldwide, LLC has determined that a defect which relates to motor vehicle safety exists in some 2020 Rubicon Express 4.5/5.5” suspension lift kits (“kit”). Our records indicate you have purchased a potentially affected kit.

 

The reason for this recall:

An inaccurate fitment guide resulted in some Rubicon Express 4.5/5.5” suspension lift kits being sold with 40 inch tires. Rubicon Express 4.5/5.5” suspension lift kits used in combination with 40 inch tires may reduce vehicle stability in certain emergency maneuvering situations, thereby increasing the risk of a crash.

 

What you should do:

You should contact TAP Worldwide, LLC’s Recall Parts Assistance Department at 1-888-376-1417 or by email at recallpartsassistance@4wp.com immediately for a replacement part or to identify a recommended service facility that is closest to you. You may replace the part yourself, or take your vehicle to a TAP Worldwide, LLC facility or your own service facility for repair. TAP Worldwide, LLC will remedy the defect without charge and at no cost to the customer.

 

What TAP will do:

If you purchased a Rubicon Express 4.5/5.5” suspension lift kit and are using it in conjunction 40 inch tires on your vehicle, TAP will replace the fitment guide and replace your 40 inch tires with 37 or 38 inch tires depending on your wheel size. If you are using the kit with tires smaller than 40 inches, TAP will replace the fitment guide only. All costs will be covered and consumers will not be charged.

 

If you have questions or if you need more information:

If you have any questions regarding this matter or any problems obtaining the necessary remedy, or if you believe that this remedy has not been completed within a reasonable time, you may contact us by phone at 1-888-376-1417, by email at recallpartsassistance@4wp.com, or by mail at

TAP Worldwide, LLC
Attn: Recall Parts Assistance
400 West Artesia Boulevard
Compton, California 90220 USA

 

If, after contacting TAP Worldwide, LLC, you still have a problem getting the above-referenced remedy completed within a reasonable time and/or without charge, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave., SE., Washington DC 20590; or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to https://www.safecar.gov.

If you are a vehicle lessor, Federal law requires that any vehicle lessor receiving this recall notice forward a copy of this notice to the lessee within ten days.

Your continued satisfaction with TAP is important to us. Please understand that we have taken this action in the interest of your safety and your vehicle’s proper operation. We regret any inconvenience that this action may cause you.

 

Sincerely,

TAP Worldwide, LLC

 

---

RUBICON EXPRESS

Technical Update

 

DATE 8/27/2020
APPLICATION 2020 JT Rubicon 4.5/5.5 Lift
PART NO. JT7147

 

TECHNICAL ISSUE

This TSB notice is sent to all installation locations where in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. TAP Worldwide, LLC has determined that a defect which relates to motor vehicle safety exists in some 2020 Rubicon Express 4.5/5.5” suspension lift kits(“kit”). This TSB is to indicate there are customer vehicles that potentially have this kit installed with 40 inch tires, and provides direction on addressing this issue.

An inaccurate fitment guide resulted in some Rubicon Express 4.5/5.5” suspension lift kits being sold with 40 inch tires. Rubicon Express 4.5/5.5” suspension lift kits used in combination with 40 inch tires may reduce vehicle stability in certain emergency maneuvering situations, thereby increasing the risk of a crash.

 

CORRECTIVE ACTION

1.Inspect vehicle tire size. If greater than 38″ go to step 2A, if 38″ or less go to step 2B.

2A. If tires are larger than 38″, let customer choose a 38″ or smaller tire of their choice at no charge, and mount balance and install. If customer has an issue with cost difference than original tire size purchased they can call customer service.

3A. Install appropriate bumpstop spacers per updated fit guide.

4A. Give customer updated fit guide.

5A. Removed 40″ tires must be shipped to 2390 Boswell Rd. Suite 400 Chula Vista, CA 91914, through transfer truck.

2B. Verify and install appropriate bumpstop spacers per fit guide, and perform safety bolt torque check.

3B. Give customer updated fitment guide.

 

Contact Tech Support
for further questions:
tech@RubiconExpress.com (877) 367-7824

 

---

1 Affected Product

Equipment

BRAND	PART NO.	PRODUCTION DATES
TAP WORLDWIDE	RUBICON EXPRESS LIFT KIT

 

---

15 Associated Documents

Defect Notice Recall 573 Report

RCLRPT-20E047-6749.PDF 214.288KB

 

---

Recall Acknowledgement

RCAK-20E047-7631.pdf 245.018KB

 

---

Defect Notice 573 Report

RCLRPT-20E047-3573.PDF 214.288KB

 

---

Recall 573 Report – Amendment 1

RCLRPT-20E047-6929.PDF 214.268KB

 

---

Recall 573 Report – Amendment 2

RCLRPT-20E047-2754.PDF 215.272KB

 

---

Recall Quarterly Report #2, 2020-4

RCLQRT-20E047-2531.PDF 211.234KB

 

---

Recall Quarterly Report #3, 2021-1

RCLQRT-20E047-8748.PDF 211.315KB

 

---

Recall Quarterly Report #4, 2021-2

RCLQRT-20E047-0180.PDF 211.419KB

 

---

ISSUED Owner Notification Letter(Part 577)

RCONL-20E047-8134.pdf 140.367KB

 

---

Remedy Instructions and TSB

RCRIT-20E047-1140.pdf 1303.944KB

 

---

Remedy Instructions and TSB

RCRIT-20E047-1990.pdf 2847.967KB

 

---

Recall 573 Report – Amendment 3

RCLRPT-20E047-9576.PDF 215.272KB

 

---

Recall Quarterly Report #1, 2020-3

RCLQRT-20E047-6341.PDF 211.124KB

 

---

Recall Quarterly Report #6, 2021-4

RCLQRT-20E047-3327.PDF 211.612KB

 

---

Recall Quarterly Report #5, 2021-3

RCLQRT-20E047-3687.PDF 211.531KB

 

---

Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20E047&docType=RCL

 

---

 

Last update on 2024-04-05 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.