GROUP: Vehicle Performance
DATE: May 11, 2016
THIS BULLETIN SUPERSEDES SERVICE BULLETIN 18-106-15 REV. A, DATED DECEMBER 24, 2015, WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDE ADDITIONAL DIAGNOSTIC TROUBLE CODE (DTC), BUILD DATES AND NEW LABOR OP.
FOR HELP WITH USING wiTECH FOR ECU FLASH REPROGRAMMING, CLICK ON THE APPLICATION’S “HELP” TAB.
THE wiTECH SOFTWARE IS REQUIRED TO BE AT THE LATEST RELEASE BEFORE PERFORMING THIS PROCEDURE.
Flash: 2.0L Diagnostic And System Improvements
This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software.
NOTE: This bulletin applies to vehicles within the following markets/countries: NAFTA.
NOTE: This bulletin applies to vehicles built on or after July 24, 2015 (MDH 0724XX) and on or before **April 25, 2016 (MDH 0425XX)** equipped with a 2.0L Engine (Sales Code ECK).
A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):
- **P0335-00 – Crankshaft Position Sensor Circuit.**
- P0456 – EVAP System Small Leak.
- P2610 – PCM Internal Engine Off Timer Performance.
- P1607 – PCM Internal Shutdown Timer Rationality.
In addition to the above DTCs, this software release also includes:
- Enhancements to the disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present.
- Re-Activation of Electronic Throttle Control (ETC) (2.0L MTX only).
- Engine oil temperature gauge calibration enhancement.
Using a scan tool (wiTECH) with the appropriate Diagnostic Procedures available in TechCONNECT, verify all engine systems are functioning as designed. If DTCs other than the ones listed above are present, record them on the repair order and repair as necessary before proceeding further with this bulletin.
If the customer describes the symptom/condition or if the technician finds the DTCs listed above, perform the Repair Procedure.
NOTE: Install a battery charger to ensure battery voltage does not drop below 13.2 volts. Do not allow the charging voltage to climb above 13.5 volts during the flash process.
NOTE: If this flash process is interrupted/aborted, the flash should be restarted.
- Reprogram the PCM with the latest software. Detailed instructions for flashing control modules using the wiTECH Diagnostic Application are available by selecting the application’s “HELP” tab.
- Clear any DTCs that may have been set in any module due to reprogramming. The wiTECH application will automatically present all DTCs after the flash and allow them to be cleared.
Reimbursable within the provisions of the warranty.
|Labor Operation No:||Description||Skill Category||Amount|
|**18-19-06-JS||Module, Powertrain Control (PCM) – Reprogram (0 – Introduction)||1 – Engine Repair and Performance||0.2 Hrs**|
NOTE: The expected completion time for the flash download portion of this procedure is approximately 4 minutes. Actual flash download times may be affected by vehicle connection and network capabilities.
The dealer must choose which failure code to use. If the customer came in with an issue and the dealer found updated software to correct that issue, use failure code CC, for all other use failure code RF.
- If the customer’s concern matches the SYMPTOM/CONDITION identified in the Service Bulletin, failure code CC is to be used.
- If an available flash is completed while addressing a different customer concern, failure code RF is to be used.
18-106-15 REV. A
Chrysler J2534 Application Overview
Flash Availability – J2534/Pass Thru Device
Vehicle to Diagnostic Tool Reference Chart
Chrysler Recommended J2534 Devices
For Chrysler recommended J2534 device, see below table.
|J2534 Device||Firmware Version|
|CTC Vehicle Box *||1.9|
|Blue Streak -2534 Global Programmer||2.10|
|Actia I+ME Passthru||2.07|
* Chrysler recommends the CTC Vehicle Box Device for Chrysler SCI ECU reprogramming. SCI reprogramming is used on most PCMs and TCMs prior to the introduction of CAN bus vehicles which began in 2004 (Durango).
Compatible J2534 Devices
Click on the link below to:
Download J2534 Application
(Install the wiTECH 2.0 J2534 Application on your computer)
Download the Setup Utility
(Configure your microPod/MDP device)
Launch wiTECH 2.0
(Once subscription and users are assigned to a tool please follow this link to access wiTECH)
- 🆚LAUNCH X431 PRO5 scan tool Upgrade all functions of X431 PRO3/X-431 Throttle III/X431-TorqueIII/X431 V+, PROS V+, PAD3. ⓵ J2534 ECU Programming &Online functions directly connect to OEM server, 50+ reset same as X-431 Throttle;⓶Bi-directional control and All system diagnostics as Snap-on scanner; ⓷ Support 150+ brands Vehicles (include CAN/CAFD/DoIP/HD protocols and AutoAuth for FCA SGW) ⓸Powered by 8-core processor(1.8GHz), Android9.0 OS, 2.4 & 5GHz WiFi connection.
- 🚜[J2534 Reprogramming With FREE SMARTBOX 3.0】Save more than $2000, LAUNCH X431 PRO5 support J2534/DOIP/CANFD/HD protocols (Needn’t buy HDIII Module,Manufacture software and non-16pin adaptors need to be purchased separately.) Download OEM software from the manufacturer’s server to 1) program data to blank/used ECUs; 2) Reflash ECUs with data loss; 3)Upgrade ECU software version. As a wireless VCI allowing the vehicle to transmit data to the diagnostic tablet without a physical connection.
- 👏[50+ Reset, Continuously Updated Reset Functions]: With the LAUNCH diagnostic tool, You will never be bothered by tricky vehicle issues and keep pace with newer technology. 50 commonly reset functions ( in the quick page ) reaching into the smallest parts to root out the problems. Extra 300+ repair functions ( in-vehicle catalog) for specific models extend the capability to reset, regeneration, initiation, matching, etc. (Functions vary by models, configurations, and systems.)
- 🌐[One stop Intelligent Diagnostic Tool]: LAUNCH X431 PRO5 obd2 scanner Bluetooth provides Repair Tips, Repair Assist, Component Measurement, TSB, Relevant Cases DTC Analysis to simplify complex diagnostic and achieve the trouble-free repair. 🤩[One Scanner For Multiple Uses]: LAUNCH diagnostic tool PRO5 collaborates with add-on modules (ADAS, Videoscope, TSGUN, X-ProG3, WiFi Pinter, Battery Tester) to expand business applications and improve diagnostic accuracy.
- 👍【2023 New OE Level Online Functions 】Bidirectional Scan Tool offers you various high-end online functions, which enable you to access the online data to do fast & complicated vehicle repairs, e.g. 1) ECU Coding for replacing, match, relearn, recode new ECU modules; 2) Online Coding for BMW, Audi, VW, Porsche, Benz to surf OEM data; 3) VAG Guided functions ease complex issues; 4) Personalization & ADAS improving car performance and driving safety.
- ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
- J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
- TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
- J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
- FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
- 🌐【Works with Autel MK908, MS908(S/Pro), MK908P, MaxiSys Elite】Autel J2534 work with these tools to program ECUs on specific BMW/ BENZ for specific functions. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your scanner MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, contact us via: 🚘auteldirect @ outlook. com🚘.
- 🌐【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
- 🌐【High-speed Transmission Speed】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed to save more times and win more business.
- 🌐【Multiple Devices Connected with PC】Autel MaxiFlash Elite J2534 also supports multiple device connections to the PC, which can operate diagnostic and reprogramming functions on more than one vehicle at the same time. Autel MaxiFlash Elite J2534 built-in wireless and data storage, which can update via Internet. It also ensures quickly reprogramming even the newest controllers.
- 🌐【Extensive Compatibility】Autel MaxiFlash J2534 is compatible with Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
- [J2534 COMPLIANT] - The Mastertech II is a J2534-1 and J2534-2 compliant VCI for OEM reprogramming and diagnostic applications
- [FULLY VALIDATED BY TOP 6 OEMS] - Mastertech II has been fully validated to operate with the top 6 OEM reprogramming applications: GM, Ford, FCA, Nissan/Infinity, Honda/Acura, and Toyota/Lexus
- [PRE-CONFIGURED] - The pre-configured wireless and wired connections make it quick and easy to connect to a vehicle from your PC (requires PC compliant with OE specifications and software)
- [RIGHT TO REPAIR] - Supports 'Right to Repair' (R2R) initiatives
- [COMPREHENSIVE KIT] - Kit includes: VCI, WiFi adapters (wireless PC to VCI), J1962 Cable (connect to vehicle), USB cable (connect to PC for firmware updates and setup), and Quick Start Guide
- 🔥🔥🔥【2023 TOP-ENHANCED HARDWARES MAKING MS908S PRO II THE CHAMPION】Autel has upgraded the MS908S Pro to MS908S PRO II with 2023 Enhanced Hardwares & Newest Functions, making it FASTER and SMARTER! Upgraded of Autel MS908S Pro/ MaxiCOM MK908P/ Elite, MS908S PRO II is most wanted with level-up performance: 🏆User-friendly Android 10 🏆5X faster Octa-core processor 🏆16M Camera 🏆Enhanced 2048*1536 display 🏆4G+128GB for fast running & data storage 🏆5G&2.4 GHz Dual WiFi for efficient updatings.
- 👍【AMAZING! 2023 NEWLY ADDED FUNCTIONS】Autel armed $300+ valued new functions to 2023 MaxiSYS MS908S PRO II with the same cost as before! Including: ✅Enhanced ECU Programming for BENZ & BMW. ✅10+ High-end Functions ✅Advanced ECU Codings ✅36+ Hot Services ✅Full Bidirectional ✅👉🏆Diagnostics for Tesla & McLaren cars 👉🏆VIN/ License SCAN 👉🏆WIFI Print 👉🏆D-PDU/RP1210 ✅ BT506/ MP408/ MV108 support ✅FCA & RENAULT SGW. ✅NO IP-Restrict, English ONLY 😎👊Autel always pursues HIGH PRODUCTS for you!
- 👍【ONE-STOP ECU PROGRAMMING FOR BENZ/ BMW & J2534 DEVICE EXTENDED PROGRAMMING ABILITY FOR MULTI-CARS】Coming with J2534 device, Autel MS908S Pro II is competent for ECU programming/ ECU Online coding/ adaption for BENZ/ BMW cars. It can program blank ECU, adapt existed ECU, match components, reflash second-hand ECU, unlock hidden functions, etc.👍👉J2534 device ALONE can also work with P-C OE-softwares to program other cars, like Ford, GM, Honda, etc. 🚦📢👉OE-softwares need to BUY from car webs.
- 👍【ADVANCED ECU CODING, CUSTOMIZE YOUR CARS】Automotive diagnostic scan tool MS908S Pro II features Advanced ECU Coding, so you can use it to customize your cars as needed by disabling some unneeded OEM settings (like auto start-stop, chimes, etc), or activating the hidden features pre-programmed to car computer to get high-end functions (like US-style daytime light, auto door look at a particular speed, etc).👉Compatible with BENZ, BWM, VW, Audi, Skoda, etc.
- 👍【36+ MAINTENANCE SERVICES & VAG GUIDED FUNCTIONS】Same as Autel MSUltra/ MS919/ MS909/ Elite II, Autel MaxiSYS MS908S PRO II features 36+ services for 10,000+ vehicles, such as crankshaft relearn, Oil Reset, EPB, SAS, A/F Setting, Throttle, Suspension, Headlamp, IMMO (basic), Injector Coding, Power Balance, BMS Reset, Brake Bleed, etc. 🚦📢👉Guided Functions provides step-by-step guidances to complete complex service operations for VAG cars, like: Bently, VW, Audi, Skoda, Seat, etc.
- Industry-leading J2534 Pass-Thru Technology: Enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. Economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Each type (see single branded types above) Mongoose-Plus is engineered to work with one of the following OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, & VW/Audi.
- Supports Current Toyota / Lexus / Scion Vehicles: Enables diagnostics, programming and other “dealer” functions through OEM applications
- NEW Bluetooth Wireless Options Available: Providing wireless connectivity between your laptop and the Mongoose-Plus
- Expert Product Support: Staffed by technicians who understand vehicle repair and J2534 Pass‑Thru applications to help you with any technical setup questions
- Key Registration and Immobilizer Support: Using NASTF Vehicle Security Professional credentials
- As a multi-protocol Pass-Thru vehicle interface, MaxiFlash Elite is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device. Specially designed to provide users with convenient PC communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, MaxiFlash Elite offers the most significant features desired by OEM customers: reliability, fast performance and flexibility.
- MaxiFlash Elite is an accessory tool for MK908P, MS908S Pro, MaxiSys Elite to program ECUs on specific for BMW and for Benz vehicles, in case you lost the J-2534 programmer.★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your tablet MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, Please contact us.
- Wireless with advanced networking functions:Built-In Wireless with advanced networking functions and data storage. Fast performance ensures reprogramming even the newest controllers & Internet upgradable and updatable.Rugged design capable of withstanding harsh environments *Internet updateable.
- Fully compatible with both SAE J2534-1 and J2534-2 gram standards *Performs the standard PassThru J2534 functionality *Compatible with for Toyota Techstream, for Volvo VIDA, for Honda HDS, for Jaguar-Land Rover IDS and for BMW 3G for OEM diagnostics,Fast performance ensures quickly gram even the newest controllers.
- All in one kit. Everything you need to reprogram vehicles in your shop. Includes OEM software and we do the programming for you.
- Stop sending vehicles to the dealer or calling a mobile technician. We do the programming for you.
- Includes hardware, OEM software, voltage maintainer and access to our team of remote experts so vehicles can be reprogrammed in your shop hassle‑free.
- Call to schedule your programming session, plug it in, and we do the rest!
- Currently covers BMW, Chrysler, Ford, GM, Toyota, Honda, Hyundai / Kia, Mercedes and Nissan.
- Featured with a brand-new upgrade system, X-431 PRO5 is newly designed for All Makes, All Models, and Full system diagnosis and assists the technician to make the vehicle diagnosis and repair easier at all skill levels.
- [J2534 ECU Reprogramming Tool, No IP Limitation]: LAUNCH X431 PRO5 scan tool Upgrade all functions of X431 V+, PROS V1.0, PAD3. With the SmartBox3.0 can download the OEM software from the manufacturer’s server for free.
- [3 IN-1 FREE J2534 ECU Programming Device: LAUNCH X431 PRO5 support all new J2534/DOIP/CANFD protocols to access data and OE programming downloads for most Car; Support DC9-36V for HD Vehicle ( No NEED buy HD Module, SAVING $900+.)
- [ One-stop Intelligent Tools]: Workshop level scan tool X431 PRO5 with the repair fix solutions database, Code Assist, Repair Tips,Component Measurement, TSB, Relevant Cases,DTC Analysis to simplify complex diagnostic and achieve the trouble-free repair.
- [50+ Reset, Continuously Updated Reset Functions]: 50 resets reaching into the smallest parts to root out the problems. Extra 300+ repair functions ( in-vehicle catalog) for specific models extend the capability to regeneration, initiation, matching, etc.
- 👍【Why Choose LAUNCH scanner X431 PRO5】It is the original LAUNCH X431 scan tool, the 2023 upgraded version of PROS V+, X431 PRO3 and V+ 4.0, which is a worthwhile investment for repair shops and mechanics. LAUNCH X431 PRO 5, all is set to OE-level standards with 1) J2534 ECU Programming & 50+ service same as PAD Series; 2) Bi-directional control + All system diagnostics as Snap-on scanner; 3) Online Coding functions directly connect to OEM server; 4) support 150+ brands Wordlwide from 1996-2023.
- 👍【J2534 Programming with Smart Box 3.0】 What is super SmartBox 3.0 VCI? Worth 1000$, Smart Box 3.0 is backed on new J2534/CANFD/DOIP, which enables you to run 14x quicker data trans and advanced OEM J2534 reprogramming for B-MW, Ben-z, F-ord, Jaguar, Land Rover, GW, Volvo, etc. (please reach to us for more details). It also serves as a wireless VCI allowing the vehicle to transmit data to the diagnostic tablet without a physical connection.
- 👍【LAUNCH X431 PRO 5 with Powerful 50+ Services】Especially designed for pro mechanics and big repair shops, Launch X431 scanner PRO5 is equipped with 50+ hot reset functions for 150 car makes which same as X431 PAD serious. Easy to navigate and help you do ABS Bleeding, TPMS Reset, Oil Reset, EPB Reset, Suspension, BMS, Injector Coding, IMMO, Power balance, Throttle Matching and more. 🚩Notice: we offer 2-year f ree update while other brands generally 1 year.
- 👍【A-ctive Test + Local-smith Level ECU Coding】Come with appealing bi-directional control to troubleshoot all possible problems for full systems within 5 minutes. This LAUNCH X431 PRO scanner even develops all practical functions needed by all technicians: 1) ECU Coding for replacing, match, relearn, recode new ECU modules; 2) Online Coding for B-MW, VW, Porsche, Ben-z to surf OEM data; 3) VAG Guided functions ease complex issues; 4) Personalization & ADAS improving car performance and driving safety.
- 👍【All System Diagnostics for 99% Vehicle Coverage] Serve for 150+ American, Asian, European brands, and cover 99% of vehicle models worldwide. This LAUNCH diagnostic scan tool can operate complete full-function diagnostics to all on-board systems to troubleshoot and repair all vehicle problems, including Engine, Transmission, Airbag, ABS, ESP, TPMS, Immobilizer, Gateway, Steering, Radio, Air Conditioning, etc.
Last update on 2023-02-25 / Affiliate links / Images from Amazon Product Advertising API
This product was presentation was made with AAWP plugin.