Safety Recall W31 – Rear View Camera – 2019-2020 Dodge Challenger

April 2, 2020 NHTSA CAMPAIGN NUMBER: 20V191000

Rearview Image Can Remain on Display/FMVSS 111

The lingering rearview image can distract the driver, increasing the risk of a crash.

 

NHTSA Campaign Number: 20V191

Manufacturer Chrysler (FCA US LLC)

Components BACK OVER PREVENTION

Potential Number of Units Affected 318,537

 

Summary

Chrysler (FCA US LLC) is recalling certain 2020 Jeep Gladiator and Jeep Cherokee, 2019-2020 Ram 1500 Pickup, Ram 2500 Pickup, Ram 3500 Pickup, Chrysler Pacifica, Dodge Durango, Jeep Grand Cherokee, Jeep Wrangler, and Jeep Renegade and 2019 Dodge Challenger vehicles equipped with 8.4″ or 12″ radio displays. A software error can cause the rearview camera image to remain displayed after the vehicle has been shifted out of reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, “Rearview Mirrors.”

 

Remedy

Chrysler has notified owners, and dealers will update the radio display software, free of charge. Optionally, owners can choose to remotely update their software via an Over-The-Air update available as of May 1, 2020. The recall began April 27, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler’s number for this recall is W30-W37.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 

Check if your Vehicle has a Recall

---

Revision 2 May 2020

Dealer Service Instructions for:

Safety Recall W31 / NHTSA 20V-191 VP4 Radio Software

 

NOTE: Added NEW LOP for “UCS” and “UAS” Radio

NOTE: Added NEW information on pages 4, 5, 8, 10 and 11

 

Remedy Available

 

 

NOTE:  This recall applies only to the above vehicles equipped with an 8.4” radio display (sales code RFL).

 

NOTE:  Some vehicles above may have been identified as not involved in this recall and therefore have been excluded from this recall.

 

 

 

Subject

The radio on about 1,036 of the above vehicles may be equipped with a radio that may allow for the rear view camera to be displayed longer than the time allowed per FMVSS No. 111.

The condition above fails to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 111, Rear Visibility, S6.2.4 Linger time requires that “The rearview image meeting the requirements of S6.2.1 and S6.2.2 shall not be displayed after the backing event has ended.” S4. Definitions, “Backing event” is defined as “an amount of time which starts when the vehicle’s direction selector is placed in reverse, and ends when the vehicle forward motion reaches a continuous duration of 10 seconds.” In certain situations, the rearview image in suspect vehicles will linger until a drive cycle ends, which can be longer than 10 seconds. If the rearview image is displayed after the backing event has ended, a driver may be distracted by the image which can cause a vehicle crash without prior warning.

 

Repair

The radio software will need to be inspected and if required updated on all of the above-mentioned vehicles.

 

Parts Information

No parts are required to perform this service procedure.

 

Parts Return

No parts return required for this campaign.

 

Special Tools

The following special tools is required to perform this repair:

 

 

Service Procedure

A. Inspect the radio software version

 

1. Turn the ignition to the “RUN” position.

 

2. Turn the radio to the “ON” position.

 

3. Press and hold the two lower corners of the radio display screen simultaneously until the “Dealer Mode” screen appears, approximately seven seconds, and then release the buttons.

 

4. Select “Radio Part Information”.

 

5. Is the radio “Application Version” 4, MR28.3, or MR28.32 for 8.4” radio and NR28.1, LR30.21, LR30.22, and LR33.3 for 12” radio? (Figure 1).

 

• NO – The radio software is current. No further action required.

 

NOTE: Uconnect website might indicate a software update is available for radio’s that have software IR22.6 or lower, if it does do not update the software.  

 

• YES – There is radio software update available. Please continue to section  Software Download

 

Figure 1 – Application Version Display

 

NOTE: Before software reflash, please enter the Dealer Mode ->Connectivity screen verify MSISDN and ICCID numbers. If those 2 fields are blank, do NOT proceed with the software reflash process, order a replacement. Replace radio under warranty, use Inspect LOP to close recall (Figure 2 and 3).

 

Figure 2 – MSISDN Information

 

Figure 3 – ICCID Information

 

B. Software Download

 

1. To download the Software Update to a USB Flash Drive it must:

 

• A USB Flash Drive must be at lease 8GB or higher.

 

• The flash drive must not contain any files (including documents, music, or pictures).

 

2. Plug the flash drive into the computer and make sure it is active and ready to Record the name of the USB flash drive and the drive location.

 

3. Format the USB flash drive (FAT32).

 

4. Confirm that there are no files or folders on the USB Flash drive. This is done to ensure that there are no conflicting files that may interrupt the software update process.

 

5. Leave the USB Flash drive in the computer and proceed to the next step.

 

6. Go to Dealer CONNECT.

 

7. Select the “Service” tab.

 

8. Select “Uconnect” from the Uconnect Command Center.

 

9. Select “Uconnect Dealer Software Downloads”.

 

NOTE: If a security message appears ‘Do you want to view only the web page content that was delivered securely?” select “NO” and continue (Figure 4).

 

10. Enter the VIN into Dealer Update ePortal and select “Go”.

 

11. Select Software Release ID.

 

Figure 4 – Security Warning

 

12. Select the “MAC” operating system (OS) only (Figure 5).

 

NOTE: Be sure to download the file to your designated folder before extracting the zip file to the blank USB flash drive.

 

13. Select the download directly to your browser.

 

14. Select the downloaded file and extract the file to the jump drive record the campaign number on the jump drive.

 

15. Safely remove the jump drive from your computer.  

 

Figure 5 – Operating System Selection

 

A blank USB flash drive will be needed for each radio update; additional updates cannot be on the same USB flash drive.

 

Unzip all the files to the root folder of USB flash drive. Files should not be within a zip folder. 

 

NOTE: The jump drive should look like (Figure 6).

 

Figure 6 – Jump Drive Mapping

 

16. Proceed to update the radio software file on the vehicle in section C. Radio Software Update.

 

C. Radio Software Update

 

1. Open the hood. Install a battery charger and verify that the charging rate provides 13.0 to 13.5 volts.  Do not allow the charger to time out during the meter may not be sufficiently accurate.  Voltages outside of the specified  flash process.  Set the battery charger timer (if so equipped) to continuous charge.

 

NOTE:  Use an accurate stand-alone voltmeter.  The battery charger volt range will cause an unsuccessful flash.  If voltage reading is too high, apply an electrical load by activating the park or headlamps and/or HVAC blower motor to lower the voltage.

 

CAUTION: Make sure no other device is plugged into any of the USB ports while performing the software update. If other devices are connected to the USB ports during the software update, it may cause failure to the files to be loaded which may cause radio damage and will need to be replaced. 

 

2. Remove all devices (SD, USB, and AUX) from the media hub.

 

3. Insert the USB flash drive containing the downloaded software into the vehicle USB port.

 

4. Turn the ignition to the “ON” position.

 

5. Turn the radio to the “ON“ position.

 

6. If the current version” and “Update To” are the same Press “OK” and  remove the USB flash drive  (Figure 7).

 

Figure 7 – Update Screen

 

 NOTE: The software update screen may take up to a minute before it is displayed. If the software update is not displayed, cycle the ignition to the “OFF” position and then to the “RUN” position.

 

7. If the screen displays “Cannot Update Software” the USB flash drive was not set up correctly. Use a top name brand USB and create a new flash drive and start the update again (Figure 8).

 

Figure 8 – Software Not Compatible

 

NOTE: If you receive an Error 01 message, verify the USB was created properly. If error persists reformat the drive and begin again.

 

8. Select the ‘Update Now” button (Figure 9).

 

Figure 9 – Software Selection

 

NOTE: Do not turn off the ignition or remove the USB until you see the update NOT available screen

 

9. Updating screen will be displayed (Figure 10).

 

Figure 10 – Updating Screen

 

10. The radio will reboot and the update will begin. The update should only take 20 minutes, the timer on the screen may display the incorrect time remaining (Figure 11).

 

Note: If the radio update fails along the way you may receive an Error message on the screen; DO NOT remove the USB at this time. The radio will roll back to the previous software level and attempt the radio update up to three times. Please allow up to 15 minutes for the rollback to occur Figure 11 _– Software Update Progress before the update retries.

 

11. After the update has completed, the radio will shut down. With the USB flash drive still inserted in the USB port. If the radio has been updated correctly, the screen will be displayed. Press “OK” and remove the USB flash drive (Figure 12).

 

NOTE: The vehicle may require a 40-minute sleep cycle to return to full functionality.

 

12. Start a wiTECH session and clear fault codes.

 

Figure 12 – Software Updated Screen

 

NOTE: After performing the radio update, the radio display screen may have a ghost image that will not clear, even after turning off the ignition. This ghost image may appear on any radio screens selected. Do not replace the radio for this concern. Other features that may be unavailable would include apps, performance or off-road pages, and connectivity. Turn the vehicle off and allow the radio and vehicle to enter a full power down cycle.

A full power down cycle may take between 45 to 60 minutes.

 

Completion Reporting and Reimbursement

 

Claims for vehicles that have been serviced must be submitted on the DealerCONNECT Claim Entry Screen located on the Service tab.   Claims paid will be used by FCA to record recall service completions and provide dealer payments.

Use the following labor operation numbers and time allowances:

 

NOTE:  See the Warranty Administration Manual, Recall Claim Processing Section, for complete recall claim processing instructions.

 

Dealer Notification

To view this notification on DealerCONNECT, select “Global Recall System” on the Service tab, then click on the description of this notification.

 

Owner Notification and Service Scheduling

All involved vehicle owners known to FCA are being notified of the service requirement by first class mail.  They are requested to schedule appointments for this service with their dealers.  A generic copy of the owner letter is attached.

 

Vehicle Lists, Global Recall System, VIP and Dealer Follow Up

All involved vehicles have been entered into the DealerCONNECT Global Recall System (GRS) and Vehicle Information Plus (VIP) for dealer inquiry as needed.

GRS provides involved dealers with an updated VIN list of their incomplete vehicles.  The owner’s name, address and phone number are listed if known.  Completed vehicles are removed from GRS within several days of repair claim submission.

To use this system, click on the “Service” tab and then click on “Global Recall System.”  Your dealer’s VIN list for each recall displayed can be sorted by: those vehicles that were unsold at recall launch, those with a phone number, city, zip code, or VIN sequence.

Dealers must perform this repair on all unsold vehicles before retail delivery. Dealers should also use the VIN list to follow up with all owners to schedule appointments for this repair.

Recall VIN lists may contain confidential, restricted owner name and address information that was obtained from the Department of Motor Vehicles of various states.  Use of this information is permitted for this recall only and is strictly prohibited from all other use.

 

Additional Information

If you have any questions or need assistance in completing this action, please contact your Service and Parts District Manager.

Customer Services / Field Operations
FCA US LLC

---

This notice applies to your vehicle,

 [Model Year and Model]  VIN XXXXXXXXXXXXXXXXX W31/NHTSA 20V-191

 

LOGO

VEHICLE PICTURE

YOUR SCHEDULING OPTIONS

 

1. RECOMMENDED OPTION Call your authorized Chrysler / Dodge / Jeep_® / RAM Dealership 

2. Call the FCA Recall Assistance Center at 1-800-853-1403. An agent can confirm part availability and help schedule an appointment 

3. Visit mopar.com, scan the QR code below, or download the Mopar Owner’s Companion App.

 

QR Code

Get access to recall notifications, locate your nearest dealer, and more through this website or Mopar Owner’s Companion App. You will be asked to provide your Vehicle Identification Number (VIN) to protect and verify your identity. The last eight characters of your VIN are provided above.

 

DEALERSHIP INSTRUCTIONS

Please reference Safety Recall W31.

---

IMPORTANT SAFETY RECALL

VP4 Radio Software

 

Dear [Name],

 

This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.

 

FCA US has decided that certain [2019 Model Year (LA) Dodge Challenger] vehicles fail to conform to Federal Motor Vehicle Safety Standard (FMVSS) No.111, Rear Visibility.

 

It is extremely important to take steps now to repair your vehicle to ensure the safety of you and your passengers.

 

WHY DOES MY VEHICLE NEED REPAIRS?

The radio in your vehicle ^[1]   may under certain circumstances, continue to display the rearview image until a drive cycle ends. If the rearview image is displayed after the backing event has ended, a driver may be distracted by repeatedly and/or continuously shifting attention in attempt(s) to cancel the image which can cause a vehicle crash without prior warning.

 

HOW DO I RESOLVE THIS IMPORTANT SAFETY ISSUE?

FCA US will repair your vehicle ^[2] free of charge (parts and labor).  To do this, your dealer will reprogram the radio software. The estimated repair time is about a half hour. In addition, your dealer will require your vehicle for proper check-in, preparation, and check-out during your visit, which may require more time. Your time is important to us, so we recommend that you schedule a service appointment to minimize your inconvenience. Please bring this letter with you to your dealership.

 

TO SCHEDULE YOUR FREE REPAIR,
CALL YOUR CHRYSLER, DODGE, JEEP OR RAM DEALER TODAY

 

WHAT IF I ALREADY PAID TO HAVE THIS REPAIR COMPLETED?

If you have already experienced this specific condition and have paid to have it repaired, you may visit www.fcarecallreimbursement.com to submit your reimbursement request online. ^[3] Once we receive and verify the required documents, reimbursement will be sent to you within 60 days.  If you have had previous repairs performed and/or already received reimbursement, you may still need to have the recall repair performed.

 

We apologize for any inconvenience, but are sincerely concerned about your safety.  Thank you for your attention to this important matter.

 

Customer Assistance/Field Operations

FCA US LLC

---

Mr. Mrs. Customer
1234 Main Street
Hometown, MI 48371

[1] If you no longer own this vehicle, please help us update our records. Call the FCA Recall Assistance Center at 1-800-853-1403 to update your information.

[2] If your dealer fails or is unable to remedy this defect without charge and within a reasonable time, you may submit a written complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave., S.E., Washington, DC  20590, or you can call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-4249153), or go to safercar.gov.

[3] You can also mail in your original receipts and proof of payment to the following address for reimbursement consideration: FCA Customer Assistance, P.O. Box 21-8004, Auburn Hills, MI 48321-8007, Attention: Recall Reimbursement.

 

Note to lessors receiving this recall notice: Federal regulation requires that you forward this recall notice to the lessee within 10 days.

 

---

This notice applies to your vehicle,

 [Model Year and Model]  VIN XXXXXXXXXXXXXXXXX W31/NHTSA 20V-191

 

LOGO

VEHICLE PICTURE

FOR RECALL QUESTIONS

 

1. RECOMMENDED OPTION Call your authorized Chrysler / Dodge / Jeep_® / RAM Dealership

 

2. Call the FCA Recall Assistance Center at 1-800-853-1403. An agent can confirm if there are any recall repairs which must be performed on your vehicle.

 

3. Visit mopar.com, scan the QR code below, or download the Mopar Owner’s Companion App.

 

QR Code

 

Get access to recall notifications, locate your nearest dealer, and more through this website or Mopar Owner’s Companion App. You will be asked to provide your Vehicle Identification Number (VIN) to protect and verify your identity. The last eight characters of your VIN are provided above.

 

DEALERSHIP INSTRUCTIONS

Please reference Safety Recall W31.

 

IMPORTANT SAFETY RECALL

VP4 Radio Software

Dear [Name],

 

This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.

 

FCA US has decided that certain [2019 Model Year (LA) Dodge Challenger] vehicles fail to conform to Federal Motor Vehicle Safety Standard (FMVSS) No.111, Rear Visibility.

 

RECALL DESCRIPTION

The radio in your vehicle ^[1]   may under certain circumstances, continue to display the rearview image until a drive cycle ends. If the rearview image is displayed after the backing event has ended, a driver may be distracted by repeatedly and/or continuously shifting attention in attempt(s) to cancel the image which can cause a vehicle crash without prior warning.

 

YOUR VEHICLE HAS ALREADY BEEN REMEDIED

According to our service records, your vehicle’s radio software was programmed during the manufacturing process. Therefore, your vehicle has been remedied and this safety recall does not need to be performed.

 

This notification is provided for your records only. There is nothing more that you need to do.

 

WHAT IF I HAVE QUESTIONS REGARDING THIS RECALL?

If you believe the software in your vehicle ^[2] has not been installed or have questions or concerns which your dealer is unable to resolve, please contact the FCA Group Recall Assistance Center at either fcarecalls.com or 1 800-853-1403.

 

WHAT IF I ALREADY PAID TO HAVE THIS REPAIR COMPLETED?

If you have already experienced this specific condition and have paid to have it repaired, you may visit www.fcarecallreimbursement.com to submit your reimbursement request online. ^[3] Once we receive and verify the required documents, reimbursement will be sent to you within 60 days.  If you have had previous repairs performed and/or already received reimbursement, you may still need to have the recall repair performed.

 

We apologize for any inconvenience, but are sincerely concerned about your safety.  Thank you for your attention to this important matter.

 

Customer Assistance/Field Operations

FCA US LLC

 

 

Mr. Mrs. Customer
1234 Main Street
Hometown, MI 48371

[1] If you no longer own this vehicle, please help us update our records. Call the FCA Recall Assistance Center at 1-800-853-1403 to update your information.

[2] If your dealer fails or is unable to remedy this defect without charge and within a reasonable time, you may submit a written complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave., S.E., Washington, DC  20590, or you can call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-4249153), or go to safercar.gov.

[3] You can also mail in your original receipts and proof of payment to the following address for reimbursement consideration: FCA Customer Assistance, P.O. Box 21-8004, Auburn Hills, MI 48321-8007, Attention: Recall Reimbursement.

 

Note to lessors receiving this recall notice: Federal regulation requires that you forward this recall notice to the lessee within 10 days.

 

---

View as web page

URGENT SAFETY RECALL NOTICE

Your 2019 DODGE CHALLENGER R/T SCAT PACK is under recall for VP4 Radio Software.

To schedule your recall repair contact your dealership or the FCA US Recall Team  at 1-800-853-1403..

 

2019 DODGE CHALLENGER R/T SCAT PACK

 

Recall information: W31/NHTSA 20V-191

 

Visit recalls.mopar.com for more information or call the FCA US Recall Team at 1-800-853-1403.

Details of the Recall

The radio may be equipped with software that may allow for the rear view camera to be displayed longer than the time allowed. If the rearview image is displayed after the backing event has ended, a driver may be distracted by the image which can cause a vehicle crash without prior warning.

The dealership will update your radio’s software.

 

How do I schedule my FREE repair?

♦     Simply contact your Chrysler, Jeep®, Dodge or RAM dealer right away to schedule a service appointment.

We apologize for any inconvenience, but are sincerely concerned about your safety. Thank you for your attention to this important matter.

Customer Assistance/Field Operations

FCA US LLC Team

1-800-853-1403. recalls.mopar.com

 

---

04/03/2020

 

New Safety Recall Advanced Communication – W31

FCA US LLC (FCA US) has announced a safety recall on certain 2019 and 2020 Model Year (LA) Dodge Challenger vehicles equipped with an 8.4” radio display.

 

REASON FOR THIS SAFETY RECALL

Some of the above vehicles were built with an 8.4″ radio display which may under certain circumstances, continue to display the rearview image until a drive cycle ends. If the rearview image is displayed after the backing event has ended, a driver may be distracted by repeatedly and/or continuously shifting attention in attempt(s) to cancel the image which can cause a vehicle crash without prior warning.

The condition described above does not comply with Federal Motor Vehicle Safety Standard (FMVSS) No.111, Rear Visibility, S6.2.4 Linger time requires that “The rearview image meeting the requirements of S6.2.1 and S6.2.2 shall not be displayed after the backing event has ended.” S4. Definitions, “Backing event” is defined as “an amount of time which starts when the vehicle’s direction selector is placed in reverse, and ends when the vehicle forward motion reaches a continuous duration of 10 seconds.” In certain situations, the rearview image in suspect vehicles will linger until a drive cycle ends, which can be longer than 10 seconds.

 

SERVICE ACTION

FCA US will conduct a voluntary safety recall to reprogram the suspect radios with updated software. Dealers will be notified of the launch of this safety recall by way of established communication methods.  This recall is estimated to launch in 2nd Quarter of 2020.

 

We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries regarding involved vehicles.

 

Customer Services Field Operations
FCA US LLC

 

---

FCA US LLC Remedy Part Numbers
W30-37 VP4R Rear View Camera Non-Compliance
Submitted on April 2, 2020
Amended on September 24, 2020

 

RADIO PART NUMBERS BY MODEL AND MODEL YEAR

 

 

---

FCA US LLC Recall Part Numbers
W30-37 VP4R Rear View Camera Non-Compliance
Submitted on April 2, 2020
Amended on September 24, 2020

 

RADIO PART NUMBERS BY MODEL AND MODEL YEAR

 

 

---

19 Affected Products

Vehicles

 

---

73 Associated Documents

Remedy Instructions and TSB

RCRIT-20V191-3845.pdf 1430.657KB

---

Remedy Instructions and TSB

RCRIT-20V191-5715.pdf 1426.348KB

---

Remedy Instructions and TSB

RCRIT-20V191-6288.pdf 1430.708KB

---

Remedy Instructions and TSB

RCRIT-20V191-6955.pdf 1430.408KB

---

Remedy Instructions and TSB

RCRIT-20V191-1017.pdf 1431.919KB

---

Remedy Instructions and TSB

RCRIT-20V191-3960.pdf 1431.722KB

---

Remedy Instructions and TSB

RCRIT-20V191-3695.pdf 1430.942KB

---

Remedy Instructions and TSB

RCRIT-20V191-9629.pdf 1431.145KB

---

Manufacturer Notices(to Dealers,etc) – Notice re FCA US LLC (FCA US) has announced a safety recall on certain 2019 and 2020 Model Year (WK) Jeep® Grand Cherokee equipped with an 8.4” radio display

RCMN-20V191-7803.pdf 199.696KB

---

Remedy Instructions and TSB

RCRIT-20V191-3223.pdf 1431.441KB

---

Remedy Instructions and TSB

RCRIT-20V191-6801.pdf 1430.982KB

---

Remedy Instructions and TSB

RCRIT-20V191-4117.pdf 1432.286KB

---

Remedy Instructions and TSB

RCRIT-20V191-4613.pdf 1431.608KB

---

Remedy Instructions and TSB

RCRIT-20V191-7598.pdf 1431.359KB

---

Manufacturer Notices(to Dealers,etc) – Notice re FCA US LLC (FCA US) has announced a safety recall on certain 2019 and 2020 Model Year (RU) Chrysler Pacifica vehicles equipped with an 8.4” radio display.

RCMN-20V191-6651.pdf 198.451KB

---

Remedy Instructions and TSB

RCRIT-20V191-4190.pdf 1431.115KB

---

Remedy Instructions and TSB

RCRIT-20V191-3188.pdf 1432.598KB

---

Remedy Instructions and TSB

RCRIT-20V191-4649.pdf 1426.722KB

---

Remedy Instructions and TSB – VP4 Radio Software Remedy Available (W32)

RCRIT-20V191-7724.pdf 1431.151KB

---

Remedy Instructions and TSB – VP4 Radio Software Update (W30)

RCRIT-20V191-5808.pdf 1431.691KB

---

Remedy Instructions and TSB n- VP4 Radio Software Update

RCRIT-20V191-9911.pdf 1430.818KB

---

Remedy Instructions and TSB

RCRIT-20V191-2820.pdf 1545.504KB

---

Remedy Instructions and TSB

RCRIT-20V191-9993.pdf 1544.749KB

---

Remedy Instructions and TSB – VP4 Radio Software: Revision #2

RCRIT-20V191-5072.pdf 1546.324KB

---

Remedy Instructions and TSB

RCRIT-20V191-4997.pdf 1545.924KB

---

Remedy Instructions and TSB

RCRIT-20V191-9841.pdf 1545.231KB

---

Remedy Instructions and TSB – VP4 Radio Software: Revision #2

RCRIT-20V191-1743.pdf 1544.68KB

---

Remedy Instructions and TSB – VP4 Radio Software: Revision #2

RCRIT-20V191-8393.pdf 1545.407KB

---

Miscellaneous Document – Software Update Details Screenshot

RMISC-20V191-8520.pdf 271.004KB

---

Owner Notification Letter(Part 577)

RCONL-20V191-7775.pdf 521.205KB

---

Owner Notification Letter(Part 577)

RCONL-20V191-7887.pdf 519.79KB

---

Owner Notification Letter(Part 577) (w32)

RCONL-20V191-8404.pdf 515.854KB

---

Owner Notification Letter(Part 577) (W32)

RCONL-20V191-6722.pdf 520.578KB

---

Owner Notification Letter(Part 577) (W30)

RCONL-20V191-2169.pdf 520.043KB

---

Owner Notification Letter(Part 577)

RCONL-20V191-6610.pdf 520.584KB

---

ISSUED Owner Notification Letter(Part 577)

RCONL-20V191-8955.pdf 520.804KB

---

Owner Notification Letter(Part 577)

RCONL-20V191-1920.pdf 516.652KB

---

Miscellaneous Document – RADIO PART NUMBERS BY MODEL AND MODEL YEAR

RMISC-20V191-5839.pdf 229.799KB

---

Manufacturer Notices(to Dealers,etc) – Communication re FCA US LLC (FCA US) has announced a safety recall on certain 2019 and 2020 Model Year (DF) RAM 3500 10K LB Cab Chassis, (DJ) RAM 2500 Pickup, (DT) RAM 1500 Pickup vehicles equipped with an 8.4” radio display.

RCMN-20V191-8037.pdf 200.262KB

---

Manufacturer Notices(to Dealers,etc) – Notice re FCA US LLC (FCA US) has announced a safety recall on certain 2019 and 2020 Model Year (BV) Jeep® Renegade, (JL) Jeep® Wrangler, (JT) Jeep® Gladiator vehicles equipped with an 8.4” radio display.

RCMN-20V191-8865.pdf 199.643KB

---

Recall Acknowledgement

RCAK-20V191-1841.pdf 244.413KB

---

Non-Compliance Notice 573 Report

RCLRPT-20V191-4667.PDF 222.805KB

---

Miscellaneous Document – RADIO PART NUMBERS BY MODEL AND MODEL YEAR

RMISC-20V191-7543.pdf 229.929KB

---

Manufacturer Notices(to Dealers,etc) – Notification re FCA US LLC (FCA US) has announced a safety recall on certain 2019 and 2020 Model Year (KL) Jeep® Cherokee vehicles with equipped with an 8.4” radio display

RCMN-20V191-7877.pdf 199.056KB

---

Manufacturer Notices(to Dealers,etc) – Notice re FCA US LLC (FCA US) has announced a safety recall on certain 2019 and 2020 Model Year (WD) Dodge Durango vehicles equipped with an 8.4” radio display.

RCMN-20V191-6510.pdf 198.106KB

---

Manufacturer Notices(to Dealers,etc) – Notice re FCA US LLC (FCA US) has announced a safety recall on certain 2019 and 2020 Model Year (DF) RAM 3500 10K LB Cab Chassis, (DJ) RAM 2500 Pickup, (DT) RAM 1500 Pickup vehicles equipped with a 12” radio display

RCMN-20V191-0527.pdf 199.261KB

---

Manufacturer Notices(to Dealers,etc) – Notice re New Safety Recall re FCA US LLC (FCA US) has announced a safety recall on certain 2019 and 2020 Model Year (LA) Dodge Challenger vehicles equipped with an 8.4” radio display

RCMN-20V191-2791.pdf 198.406KB

---

Remedy Instructions and TSB

RCRIT-20V191-7496.pdf 1541.505KB

---

Owner Notification Letter(Part 577)

RCONL-20V191-6561.pdf 515.972KB

---

Owner Notification Letter(Part 577)

RCONL-20V191-8416.pdf 519.839KB

---

Recall Quarterly Report #1, 2020-2

RCLQRT-20V191-1369.PDF 211.16KB

---

Recall Quarterly Report #3, 2020-4

RCLQRT-20V191-9046.PDF 211.363KB

---

Miscellaneous Document – RADIO PART NUMBERS BY MODEL AND MODEL YEAR

RMISC-20V191-0507.pdf 225.221KB

---

Miscellaneous Document – Copy of owner notification letter (already remedied)

RMISC-20V191-8762.pdf 515.962KB

---

Miscellaneous Document – Copy of owner notification letter (already remedied)

RMISC-20V191-6174.pdf 516.781KB

---

Miscellaneous Document – RADIO PART NUMBERS BY MODEL AND MODEL YEAR

RMISC-20V191-9157.pdf 225.32KB

---

Miscellaneous Document – Copy of Owner notification letter (already remedied)

RMISC-20V191-4309.pdf 516.998KB

---

Miscellaneous Document – Copy of owner notification letter (already remedied)

RMISC-20V191-3023.pdf 516.059KB

---

Miscellaneous Document – Copy of Owner Notification

RMISC-20V191-2857.pdf 516.129KB

---

Miscellaneous Document – Copy of owner notification letter (already remedied)

RMISC-20V191-2236.pdf 516.76KB

---

Miscellaneous Document – Copy of owner notification letter (already remedied)

RMISC-20V191-8801.pdf 517.627KB

---

Miscellaneous Document – Copy of owner notification letter (already remedied)

RMISC-20V191-6828.pdf 517.421KB

---

Recall Quarterly Report #2, 2020-3

RCLQRT-20V191-1070.PDF 211.266KB

---

Miscellaneous Document – Owner Notification Email Blast

RMISC-20V191-8753.pdf 162.605KB

---

Miscellaneous Document

RMISC-20V191-9198.pdf 225.224KB

---

ISSUED Renotification Notice

RCRN-20V191-4513.pdf 137.972KB

---

ISSUED Renotification Notice

RCRN-20V191-5823.pdf 137.975KB

---

ISSUED Renotification Notice

RCRN-20V191-2596.pdf 137.975KB

---

ISSUED Renotification Notice

RCRN-20V191-8012.pdf 137.996KB

---

ISSUED Renotification Notice

RCRN-20V191-8416.pdf 138.005KB

---

ISSUED Renotification Notice

RCRN-20V191-8708.pdf 137.017KB

---

ISSUED Renotification Notice

RCRN-20V191-1019.pdf 137KB

---

ISSUED Renotification Notice

RCRN-20V191-4775.pdf 138.008KB

---

Latest Recalls Documents

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V191&docType=RCL

 

---

 

Last update on 2022-05-17 / Affiliate links / Images from Amazon Product Advertising API