GROUP: Vehicle Performance
DATE: August 14, 2008
Flash: Long Crank Times
|2008||(LX)||300 / Magnum / Charger|
NOTE: This bulletin applies to models equipped with a 5.7L engine (sales code EZB).
Some customers may complain of long crank times. A software change has been made to the crank synchronization algorithm to improve the start time.
If the vehicle owner complains of this issue reprogramming the PCM with the new software.
Using a Scan Tool (StarSCAN) with the appropriate Diagnostic Procedures available in TechCONNECT, verify all engine systems are functioning as designed. If DTC’s are present record them on the repair order and repair as necessary before proceeding further with this bulletin.
|1||04275086AB||Label, Authorized Modification|
SPECIAL TOOLS / EQUIPMENT REQUIRED:
|CH9404D||StarSCAN Vehicle Cable|
|CH9409||StarSCAN Documentation Kit|
|CH9410||StarSCAN Ethernet Cable, 12 ft.|
|CH9412||StarSCAN Software Update Device Kit|
|TechCONNECT PC or equivalent|
REPAIR PROCEDURE – USING THE INTERNET TO RETRIEVE THE FLASH FILE:
- Reprogram the PCM with the latest software. Follow the detailed service procedures available in DealerCONNECT/TECHCONNECT, Refer To 8 – Electrical/Electronic Control Modules/Powertrain Control Module – Standard Procedure PCM/ECM Programming – Gas.
- Type the necessary information on the “Authorized Modification Label” p/n 04275086AB and attach it near the VECI label.
Reimbursable within the provisions of the warranty.
|Labor Operation No:||Description||Amount|
|18-19-06-D5||Module, Powertrain Control (PCM) – Reprogram (B)||0.4 Hrs.|
THE StarSCAN FLASH FILES FOR THIS BULLETIN MUST BE RETRIEVED FROM THE INTERNET.
StarSCAN SOFTWARE LEVEL MUST BE AT RELEASE 9.01 OR HIGHER FOR THIS BULLETIN.
StarMOBILE STANDALONE MODE OR StarMOBILE DESKTOP CLIENT MAY ALSO BE USED TO PERFORM THIS PROCEDURE.
Chrysler J2534 Application Overview
The Chrysler J2534 System is a combination of the J2534 Application (2010 and newer Model Year Support) and the Chrysler J2534 Flash Application (2009-1996 Model Year Support). J2534 aftermarket users are required and responsible for installing the J2534 device driver provided by the device manufacturer. If you need support installing the device driver software contact the device manufacturer. See the related article “Chrysler J2534 Manual” for additional information. Chrysler J2534 application provides below capabilities:
|The Chrysler J2534 Flash Application:|
|Application Usage and Support|
Chrysler Recommended J2534 Devices
|J2534 Device||Firmware Version|
|CTC Vehicle Box *||1.9|
|Blue Streak -2534 Global Programmer||2.10|
|Actia I+ME Passthru||2.07|
* Chrysler recommends the CTC Vehicle Box Device for Chrysler SCI ECU reprogramming. SCI reprogramming is used on most PCMs and TCMs prior to the introduction of CAN bus vehicles which began in 2004 (Durango).
Chrysler J2534 System Support:
Chrysler J2534 System
PC Requirements for Chrysler J2434 System:
Chrysler J2434 System Release Notes:
Please click here to view the Application Release Notes.
Chrysler J2434 System Download:
Chrysler ECU Flash Availability matrix:
A harness adaptor is required to update certain vehicles. The following tables list which vehicles / modules require which adaptor. Adaptors can be purchased through the SPX Miller Special Tools program. See SPX Miller Special Tools program for details.
MLR-J2534-MMC required on:
|SBEC III||1996 – 1997||SEBRING / AVENGER (FJ)|
|ETAX III||1996 – 1997||SEBRING / AVENGER (FJ)|
|SBEC IIIA||1997 – 1998||SEBRING / AVENGER (FJ)|
|ETAX IIIA||1997 – 1998||SEBRING / AVENGER (FJ)|
|Powertrain||2001 – 2201||SEBRING / STRATUS COUPE (ST)|
MLR-J2534-TCM required on:
|ETAX IIIB||2003 – 2004||SEBRING / STRATUS SEDAN (JR)|
|ETAX IVA||2005 – 2006||LIBERTY (DIESEL) JEEP (KJ)|
Additional Information and Known Issues / Concerns:
If you are reprogramming the 5.9L diesel engine controller on the 1996-2008 Dodge RAM vehicle, it is necessary to also reprogram the VIN after the ECU has been flashed. To write the VIN to the ECU, you may use aftermarket software support, or use an OEM FCA US LLC scan tool (DRBIII or StarSCAN). For more information, see the FCA US LLC Scan Tool Lease Options section.
- 1996-2009 ALL PCMs
If you are REPLACING a PCM or ECM and the vehicle is equipped with a theft deterrent system (Sentry Key), it must be initialized to properly function with the Anti Theft module. You also need to reprogram the VIN when replacing a PCM or ECM. To write the VIN to the ECU and initialize the PCM to work with the theft deterrent system, you may use aftermarket software support, or use an OEM FCA US LLC scan tool (DRBIII or StarSCAN). For more information, see the FCA US LLC Scan Tool Lease Options section.
FCA US LLC Scan Tool Lease Options:
- For 2009 model year vehicles and prior, it may be necessary to use either a DRBIII or a StarSCAN to perform function required after ECU replacement. To lease the DRBIII call 1-586-532-8400 or click here.
- Beginning with 2010 MY, function required to replace an ECU will be supported via the J2534 application.